Experimental and finite element studies of the rotary friction welding (RFW) process of tungsten heavy alloy (THA) with aluminium alloy 5XXX series are presented. A 2.5D torsion simulation model including the circumferential effects was developed in this study. The temperature distributions, effective stress, flash dimensions and axial shortening were calculated on un-rotated friction welding aluminium parts. The peak temperatures were measured both in the axis and at the half-radius of the specimen. The maximum interface temperature of 581 °C for the friction weld was below the melting temperature of the aluminium alloy. The experimental and numerical results of the temperature and final weld geometries show good agreement between them. The results indicate very small deviations of 4.45%, 2.96%, and 2.34% on the flash width, flash height and axial shortening of friction welds.
The aim of this paper is to analyse the mechanical properties of butt joints between S355 steel and 6061-T6 aluminium alloy, as well as their relationship to changes in the structure of the material caused by welding. The effect of the tool offset was analysed in particular. For the analysis, tensile tests were carried out using macro- and mini-specimens taken from S355/AA6061-T6 joints and base materials. In addition, the macro- and microstructure of the joints was determined, the hardness profiles in the joints were analysed, and fractographic analysis of the fractures of the specimens was carried out. Based on the results of the macro- and microstructure examinations, typical friction stir welding (FSW) joint zones were characterised. The microstructure was observed in the interface line of the materials on the root side, the negative effect of which on the quality of the joint was confirmed by digital image correlation (DIC) strain analysis during the monotonic tensile test. The highest average value of su = 141 MPa for the entire joint was obtained for a 0.4 mm tool offset. The highest average value of su = 185 MPa for the selected joint layer was obtained for a 0.3 mm tool offset. Fracturing of the joint in the selected layer for the tool offset values of 0.3 mm and 0.4 mm occurred in the weld nugget zone (WNZ) where the lowest hardness was recorded.
Experimental and FEM studies of the friction welding process of spheroidal graphite cast iron (SGCI) are presented. A coupled thermal and mechanical 2.5 D FEM model was used to simulate the continuous drive friction welding (CDFW) process. The FE model predicted the peak temperature of the joint, effective stress, axial shortening, and the weld flash size. Additionally, the friction force on the axial shortening of specimens was studied. The peak temperatures were measured both on the axis and at the surface of the specimen. The predicted maximum temperatures in the axis, ½ radius, and 2 mm from the surface of the sample amounted to 1162 °C, 1177 °C, and 1061 °C, respectively. The maximum temperature of the spheroidal graphite cast iron joint was below the melting temperature of the base material (~1350 °C). The predicted temperature curves, outbursts, and shortening of welded elements indicated a good match with real models.
Thermoplastic fiber metal laminates (TFMLs) are lightweight hybrid materials combining metallic layers with fiber-reinforced thermoplastic composites, offering a high strength-to-weight ratio. Existing studies indicate a limited range of polymer matrices used in such structures, most commonly polyamide 6 (PA6). In this work, polybutylene terephthalate (PBT) was selected as a potential alternative matrix because literature data indicate its lower moisture absorption and good dimensional stability compared with PA6. A comparative analysis of TFMLs based on aluminum and carbon fabric-reinforced composites with PA6 and PBT matrices was conducted. Static tensile tests were performed on base materials, composites, and laminates, supported by analytical modeling using the superposition method and fractographic analysis. The results showed that fiber orientation and polymer content significantly affect stiffness, strength, and damage evolution. Fiber orientation remains the governing factor, controlling load transfer and damage initiation. Laminates with 0/90° fibers exhibited the highest strength, while ±45° configurations showed reduced performance due to shear-dominated deformation. The polymer primarily acts as a matrix, ensuring structural integrity, with comparable mechanical properties for both systems. Delamination at the metal–composite interface was identified as the dominant failure mechanism.