Zbigniew Grzesik

Prof. Dr. Zbigniew Grzesik


Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 October 2012 in High Temperature Materials and Processes
Verified
Journal Article
Open access
AKA. Kaczmarska
A. Kaczmarska
ZGZbigniew Grzesik
Zbigniew Grzesik
SMS. Mrowec
S. Mrowec
Defect structure and transport properties of Co 3 O 4 cobalt oxide have been studied as a function of temperature and oxygen pressure, using marker and thermogravimetric techniques. It has been found that the oxidation of CoO to form Co 3 O 4 follows parabolic kinetic, being thus diffusion controlled. Marker experiments have demonstrated that cation sublattice of Co 3 O 4 oxide is predominantly disordered, but the defect structure is rather complex. At very low oxygen pressures, close to the dissociation pressure of the oxide, interstitial cations are the predominant point defects, while at high pressures cation vacancies predominate. This behavior is reflected in complex dependence of the parabolic rate constant of CoO oxidation on oxygen pressure. At low pressures, namely, parabolic rate constant of the reaction increases with oxygen pressure, reaching then virtually constant value in intermediate pressure range and increases again in highest pressure range. Theoretical analysis of kinetic results in terms of point defect thermodynamics confirmed the above conclusion, concerning complex defect structure of Co 3±y O 4 oxide. Finally, self-diffusion coefficient of cations in the discussed oxide has been calculated as a function of temperature and oxygen pressure from kinetic rate measurements, using Wagner's theory of metals oxidation.

10 April 2018 in Coatings
Verified
Journal Article
Open access
PDF file
Karol KyziolKarol Kyziol
Karol Kyziol
JOJulia Oczkowska
Julia Oczkowska
DKDaniel Kottfer
Daniel Kottfer
MKMarek Klich
Marek Klich
Łukasz KaczmarekŁukasz Kaczmarek
Łukasz Kaczmarek
ZGZbigniew Grzesik
Zbigniew Grzesik
In this paper, the surface properties and selected mechanical and biological properties of various multi-layer systems based on diamond-like carbon structure deposited on low-density polyethylene (LDPE) substrate were studied. Plasma etching and layers deposition (incl. DLC, N-DLC, Si-DLC) were carried out using the RF CVD (radio frequency chemical vapor deposition) method. In particular, polyethylene with deposited N-DLC and DLC layers in one process was characterized by a surface hardness ca. seven times (up to ca. 2.3 GPa) higher than the unmodified substrate. Additionally, its surface roughness was determined to be almost two times higher than the respective plasma-untreated polymer. It is noteworthy that plasma-modified LDPE showed no significant cytotoxicity in vitro. Thus, based on the current research results, it is concluded that a multilayer system (based on DLC coatings) obtained using plasma treatment of the LDPE surface can be proposed as a prospective solution for improving mechanical properties while maintaining biocompatibility.

12 February 2019 in Oxidation of Metals
Verified
Journal Article
Open access
PDF file
GSGrzegorz Smola
Grzegorz Smola
RGRichard Gawel
Richard Gawel
Karol KyziolKarol Kyziol
Karol Kyziol
MMMaria Miszczak
Maria Miszczak
ZGZbigniew Grzesik
Zbigniew Grzesik
The oxidation behavior of four valve steels (X33CrNiMn23-8, X50CrMnNiNbN21-9, X53CrMnNiN20-8 and X55CrMnNiN20-8) covered with thin sputter-deposited coatings containing chromium and nickel was studied under isothermal and thermal shock conditions. It was determined that coated steels exhibit greater resistance against oxidation than steels with unmodified surfaces. This effect results from the formation of chromium-rich oxides (e.g., Cr2O3, NiCr2O4, MnCr2O4) during oxidation of the surface modified steel. These oxides exhibited better protective properties than the products grown on unmodified steels (namely Fe3O4 and Fe2O3). The entirety of the obtained experimental results confirms the possibility of increasing the scaling resistance of valve steels by using around 1-µm-thick chromium-rich protective Cr–Ni coatings.

3 February 2013 in Oxidation of Metals
Verified
Journal Article
Open access
PDF file
ZGZbigniew Grzesik
Zbigniew Grzesik
GSGrzegorz Smola
Grzegorz Smola
KAK. Adamaszek
K. Adamaszek
ZJZ. Jurasz
Z. Jurasz
SMS. Mrowec
S. Mrowec
The high-temperature corrosion behavior of four valve steels (X33CrNiMn23-8, X50CrMnNiNbN21-9, X53CrMnNiN20-8 and X55CrMnNiN20-8) in combustion gases of fuel oil, containing different concentrations of bio-components (5 and 10 wt%) has been studied under thermal shock conditions. It was found that the addition of bio-components decreased the corrosion resistance of steels investigated. It was also found that the X33CrNiMn23-8 steel containing the highest chromium concentration, behaved in the investigated atmospheres much better than three remaining steels due to the formation of highly protective chromia scale.

27 July 2017 in Materiali in tehnologije
Verified
Journal Article
Closed access
MDM. Drożdż
M. Drożdż
Karol KyziolKarol Kyziol
Karol Kyziol
ZGZbigniew Grzesik
Zbigniew Grzesik

30 October 2012 in High Temperature Materials and Processes
Verified
Journal Article
Open access
PDF file
ZGZbigniew Grzesik
Zbigniew Grzesik
SMS. Mrowec
S. Mrowec
Basing on actual theoretical approach and experimental results, the mechanism of sulphide formation beneath the oxide scale grown on metals in SO 2 -O 2 atmospheres has been described. It has been shown that in spite of much lower sulphur partial pressure in the oxidizing atmosphere than the dissociation pressure of the sulphide to be formed, the sulphidation process takes place beneath the oxide scale. This, at the first sight, unexpected behavior results from the fact that sulphur is diffusing inwards through the primary oxide scale in the molecular form, i.e. SO 2 molecules. Reaching thus metal-scale interface, where the oxygen partial pressure is very low, virtually equal to the dissociation pressure of the oxide forming the scale, SO 2 ⇔ O 2 + ½S 2 equilibrium is shifted to the right, as a result of which the partial pressure of sulphur vapor dramatically increases, reaching the value several orders of magnitude higher than that needed for sulphide formation. Analogous situation is observed during oxidation of chromium steels in CO 2 -O 2 atmospheres. In this case, namely, carburisation process is observed beneath the oxide scale, in spite of the fact that carbon activity in this environment is several order of magnitude lower than that required for chromium carbide formation. This again unexpected situation becomes understandable if one assumes – like in the case of metal oxidation in SO 2 containing atmosphere – that carbon is transported through the oxide scale in the form of CO 2 molecules. The final conclusion is, that the explanation of the mechanism of sulphide formation beneath the oxide scale on metals and of carburization beneath the oxide scales on steels constitutes the important step forward, leading to the better understanding of high temperature corrosion mechanisms of metallic materials, observed in multicomponent agresive gases.