The use of shape memory polymer composites is growing rapidly in smart structure applications. In this work, an active asymmetric composite called “controlled behavior composite material (CBCM)” is used as shape memory polymer composite. The programming and the corresponding initial fixity of the composite structure is obtained during a bending test, by heating CBCM above thermal glass transition temperature of the used Epoxy polymer. The shape memory properties of these composites are investigated by a bending test. Three types of recoveries are conducted, two classical recovery tests: unconstrained recovery and constrained recovery, and a new test of partial recovery under load. During recovery, high recovery displacement and force are produced that enables the composite to perform strong two-way actuations along with multi-shape memory effect. The recovery force confirms full recovery with two-way actuation even under a high load. This unique property of CBCM is characterized by the recovered mechanical work.
26 December 2018 in Polymers for Advanced Technologies
Flax fibers are widely used as the strongest natural fibers in composite parts with advanced structures. Due to their excellent mechanical properties and recyclability, they have attracted more attention from the aviation and automotive industries, etc. These composite parts are usually obtained by preforming reinforcements or prepregs at high temperatures, and their mechanical behaviors are greatly affected by temperature variations. To improve the understanding of the mechanical properties of flax fiber materials, especially for the braided fabric with non-orthogonal structures, uniaxial tensile tests at different temperatures and tensile speeds were conducted on hollow tubular braided fabrics. The thermomechanical properties of Flax/Polyamide12 (PA12) prepregs were analyzed. The results show that temperature and tensile speed have obvious effects on the strength and shear stiffness of tubular fabrics. The strength and shear stiffness of the fabric decreases as the ambient temperature increases. Meanwhile, the strength of the fabric can also be improved by appropriately increasing the tensile speed. In addition, according to the experimental results, a theoretical model is established to describe the shear angle on the smallest circumference of the fabric, which provides a theoretical basis for the subsequent simulation process. The test results can provide a reference for the manufacture of flax fiber-reinforced composites with tubular structures.
26 February 2026 in Progress in Additive Manufacturing
Nowadays, wire arc additive manufacturing can contribute to achieving zero overproduction by enabling on-demand fabrication of metal spare parts and reducing the need for excess inventory. However, using WAAM to manufacture metal components with aluminum alloys encounters challenges due to heat accumulation in the subsequent layers, which negatively impacts the structural integrity of the final part. This study investigates a new approach called interlayer nitrogen cooling (INC) that uses nitrogen gas as a cooling medium between subsequent layers to mitigate the heat accumulation induced by different thermal cycles, resulting in better structural integrity of the final part. The study investigated a comparison between the natural cooling (NC) approach and the INC approach; the results showed that INC approach resulted in grain size refinement by about 82%, which enhanced the mechanical properties. The tensile strength increased by 26% for the INC processed walls compared to the NC. This paper will discuss the details of the cooling system, microstructure analysis, porosity formation of Al–Mg alloy and its tensile properties.
28 May 2009 in Journal of Intelligent Material Systems and Structures
The controlled behavior of composite material (CBCM) is a thermomechanical active composite using Joule effect and heterogeneous thermal elongation properties as an actuator within composite structures. An ‘active layer’ made of carbon yarns is used as internal source of heat. To help the design of this composite a simple model based on thermomechanical and composite homogenization considerations is presented. A three-point bending test is used to compare the calculated results to experimental results. A good accordance between the relevant data (maximum of deflection and temperature on the plate) at stabilization being observed, the model is used to study the influence of some parameters. The position of the active layer, a design parameter of great importance, is particularly studied and an optimized solution is proposed. Then, the model is used for a sensitivity analysis of some design and working parameters. Finally, the results of a FEM model are compared to the previous.
For shape morphing application, thermal activation coupling to a bimetallic strip effect can be a substitute for classical actuators, piezoelectrical or shape memory alloys. The controlled behaviour of composite material (CBCM) is a thermaly activated composite material. The thermal activation is made thanks to carbon yarns which are connected to a power supply. If the anisotropy of the structure is well organized, the desired deformation is reached when the temperature within the composite is rising. To obtain a CBCM morphing composite structure, it is necessary to design a specific structure. The aim of this work is to show that it is possible to adapt the CBCM principle in order to transform any kind of classical composite structure to an active structure. The first part of this work consists in presenting the experimental results for two examples of composite beams. The second part is about the active structure FEM modeling and the development of adapted tools for this particular design.