Synthetic rubbers fabricated from 1,3-butadiene (BD) and its substituted monomers have been extensively used in tires, toughened plastics, and many other products owing to the easy polymerization/copolymerization of these monomers and the high stability of the resulting material in manufacturing operations and large-scale productions. The need for synthetic rubbers with increased environmental friendliness or endurance in harsh environments has motivated remarkable progress in the synthesis of BD and its substituted monomers in recent years. We review these developments with an emphasis on the reactive routes, the products, and the synthetic strategies with a scaling potential. We present reagents that are primarily from bio-derivatives, including ethanol, C4 alcohols, unsaturated alcohols, and tetrahydrofuran; the major products of BD and isoprene; and the by-products, activities, and selectivity of the reaction. Different catalyst systems are also compared. Further, substituted monomers with rigid, polar, or sterically repulsive groups, the purpose of which is to enhance thermal, mechanical, and interface properties, are also exhaustively reviewed. The synthetic strategies using BD and its substituted monomers have great potential to satisfy the increasing demand for better-performing synthetic rubbers at the laboratory scale; the laboratory-scale results are promising, but a big gap still exists between current progress and large scalability.

An effective ionic liquid vacuum microwave-assisted method was developed for extraction of the thermo- and oxygen-sensitive glycosides salicin, hyperin and rutin from Populus bark due to the strong solvating effects of ionic liquids on plant cell walls. In this study, [C₄mim]BF₄ solution was selected as the extracting solution for extraction of the target analytes. After optimization by single factor experiments and response surface methodology, the optimum condition parameters were achieved, which included 1.0 M [C₄mim]BF₄, 2 h soaking time, −0.08 MPa vacuum, 20 min microwave irradiation time, 400 W microwave irradiation power and 25 mL/g liquid/solid ratio. Under the optimum conditions, higher extraction yields of salicin (35.53 mg/g), hyperin (1.32 mg/g) and rutin (2.40 mg/g) were obtained. Compared with other extraction methods, the developed method provided higher yields of the three target components after a relatively shorter extraction time (20 min). No obvious degradation of the target analytes was observed under the optimum conditions in performed stability studies and the proposed method had a high reproducibility. Meanwhile, after adsorption and desorption on macroporous D101 resin, the target analytes can be effectively separated from the [C₄mim]BF₄ ionic liquid extraction solution and the yields of salicin, hyperin and rutin were 89%, 82% and 84%, respectively. The recovered [C₄mim]BF₄ ionic liquid presented a good extraction effect on the three analytes after recycling five times.

An ionic liquid-based microwave-assisted extraction method (ILMAE) was successfully applied for the extraction of taxifolin from Larix gmelinii. Different kinds of 1-alkyl-3-methylimidazolium ionic liquids with different kinds of cations and anions were studied and 1-butyl-3-methylimidazolium bromide was chosen as the optimal solvent for taxifolin extraction. The optimal conditions of ILMAE were determined by single factor experiments and Box-Behnken design as follows: [C₄mim]Br concentration of 1.00 M, soaking time of 2 h, liquid-solid ratio of 15:1 mL/g, microwave irradiation power of 406 W, microwave irradiation time of 14 min. No degradation of taxifolin had been observed under the optimum conditions as evidenced from the stability studies performed with standard taxifolin. Compared with traditional solvent and methods, ILMAE provided higher extraction yield, lower energy and time consumption. The distribution of taxifolin in different parts of larch and the influences of age, orientation, and season on the accumulation of taxifolin were analyzed for the sufficient utilization of L. gmelinii.

A Brønsted acid ionic liquid, 3-methyl-1-(4-sulfonylbutyl) imidazolium hydrogensulfate ([HO ₃ S(CH ₂ ) ₄ mim]HSO ₄ ), was used for the first time for the preparation of a sulfonated carbon catalyst.

A microwave-assisted extraction (MAE) method was applied to separate saponins from Sapindus mukorossi pericarps. The most important factors of the six extraction parameters were selected using Plackett–Burman designs; therefore, the further extraction procedure was optimized using the Box–Behnken designs; meanwhile, the optimum processing parameters and well-pleasing saponins extraction rate were inferred. The final operation conditions were the ethanol concentration of 40%, soaking time of 3 h, particle size of 80–100 meshes, extraction time of 13 min, solvent-solid ratio of 19 mL/g, and microwave power of 425 W. Based on the optimal extraction parameters, the extraction rate of the saponins by means of MAE technique reached 280.55 ± 6.81 mg/g, which exceeds yields acquired using conventional manners. Saponins from S. mukorossi have obvious xanthine oxidase inhibitory properties in vitro compared with allopurinol. The saponins displayed a type of competitive inhibition of xanthine oxidase. In conclusion, a MAE technique in association with a response surface design provides an efficient extraction tactics, which could sufficiently isolate saponins from S. mukorossi pericarps; further, this technique could be applied to the dissociation of other bioactive substances from plant sources. In addition, the saponins may be a promising alternative to conventional medicine to treat gout and other inflammation-associated disorders to mitigate the side effects of traditional drugs.

A free-of-dust pollution extraction method combined-homogenate and ultrasonic cavitation system, namely, homogenate-combined ultrasonic cavitation synergistic extraction (HUCSE), was proposed for the efficient extraction of flavonoids from Cinnamomum camphora leaves. Response surface methodology of Box–Behnken design was employed to optimize the HUCSE process, and the optimum operation conditions attained with an extraction yield of 7.95 ± 0.27 mg/g were ethanol concentration 76%, homogenate/ultrasonic time 25 min, solvent-to-solid ratio 22 mL/g, and ultrasonic power 240 W. A second-order kinetic mathematical methodology was performed to depict the behaviors of HUCSE and heat reflux extraction method. The results suggested that the developed HUCSE is an efficient and green method for the extraction of C. camphora flavonoids or other plant natural products, where the obvious higher parameters of extraction capacity at saturation, second-order extraction rate constant, and original extraction rate were obtained when compared to the heat reflux method. The antioxidant activity assays in vitro showed that the C. camphora flavonoids possessed strong antioxidant activity and are promising to be applied as a natural alternative antioxidant.