Milad Heidari

Prof. Dr. Milad Heidari


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2021 in Physics of Fluids
Verified
Journal Article
Closed access
PDF file
KAKiumars Khani Aminjan
Kiumars Khani Aminjan
MHMilad Heidari
Milad Heidari
DGDavood Ganji
Davood Ganji
MAMaryam Aliakbari
Maryam Aliakbari
Fatemeh SalehiFatemeh Salehi
Fatemeh Salehi
MGMaryam Ghodrat
Maryam Ghodrat
Studies on pressure-swirl atomizers have mainly focused on pressure-swirl atomizers with tangential input while there are limited studies on pressure-swirl atomizers with a spiral path. This study applies experimental and computational methods to provide a better understanding of flow development in this type of atomizer at the design point and outside the design point. Experimental results showed that as the pressure increases, the spray cone angle increases. This increase initially occurs with a higher slope and then the slope is toned down. While the drainage coefficient remains constant, the droplet diameter decreases as the pressure increases. It is observed that similar to the pressure-swirl atomizer with tangential input, the pressure-swirl atomizer with a spiral path has a conical hollow spray. At the constant mass flow rate, as the spiral path cross-section, the length of the swirl chamber and orifice diameter increase, the fluid film thickness and average diameter of droplets increase while the spray cone angle reduces. Further, increasing the number of spiral paths causes a wider spray cone angle, higher discharge coefficient, larger fluid film thickness, and larger droplet diameter. The results also showed that increasing the length of the orifice marginally affected the properties of the spray while significantly reducing the spray cone angle. It is important to note that the numerical results are in good agreement with the experimental data.

14 October 2020 in Archive of Applied Mechanics
Verified
Journal Article
Closed access
PDF file
KAKiumars Khani Aminjan
Kiumars Khani Aminjan
MHMilad Heidari
Milad Heidari
PRPooyan Rahmanivahid
Pooyan Rahmanivahid

1 July 2023 in Physics of Fluids
Verified
Journal Article
Open access
PDF file
KAKiumars Khani Aminjan
Kiumars Khani Aminjan
MGMaryam Ghodrat
Maryam Ghodrat
MHMilad Heidari
Milad Heidari
AAAmin Arjmandfard
Amin Arjmandfard
PRPooyan Rahmanivahid
Pooyan Rahmanivahid
SASherzod Shukhratovich Abdullaev
Sherzod Shukhratovich Abdullaev
Air-blast atomizers are widely used in passenger aircraft engines. In these atomizers, high-speed airflow is used for improved fuel atomization, and as a result, better combustion. The key purpose of this research is to investigate the duplex air-blast atomizers according to the engine data in the real operational conditions with the help of experimental method and numerical solution. When analyzing the variations in fuel sprays under different application conditions, it is important to consider not just one but multiple parameters such as fuel mass rate, air mass rate, and combustion chamber pressure. However, analyzing the individual effects of these parameters can be challenging as they change simultaneously. To address this, a dimensionless number namely K was defined, which takes into account the combined effect of fuel mass rate, air mass rate, and combustion chamber pressure. The results showed that when K decreased by 31.25%, the spray angle of nozzle 1 and nozzle 2 increased by 10.09% and 48.15%, respectively, while the average droplet diameter caused by primary breakup for nozzle 1 and nozzle 2 decreased by 76.29% and 71.57%, respectively. The secondary breakup was somewhat similar, and for nozzle 1 and nozzle 2, the average droplet diameter decreased by 76.5% and 71.88%, respectively. It is worth noting that the average error for spray cone angle in the simulation compared to the experimental results was 6.47%. The results of this research, in addition to causing a better understanding of the atomization processes in air-blast atomizers, can be useful for aerospace engineers.

16 January 2023 in International Journal of Technology
Verified
Journal Article
Closed access
SHSahahd Hamza
Sahahd Hamza
MHMilad Heidari
Milad Heidari
MAMohammad Ahmadizadeh
Mohammad Ahmadizadeh
MDMohammadreza Dashtizadeh
Mohammadreza Dashtizadeh
MCMira Chitt
Mira Chitt
Turbines are efficient power generators. Because wind energy is a clean fuel source, it is widely utilized in some regions. One of the major factors affecting wind turbine performance is the angle of attack of the blade. The aerodynamics and efficiency can be improved by improvising the lift-to-drag ratio CL/CD to get the best design for wind turbine blades. There are many factors affecting the efficiency of horizontal wind turbine blades such as the angle of attack of the blade. Therefore, this study investigated the effect of the angle of attack on coefficients and forces, particularly on a blade with NACA 4412 airfoil in a horizontal axis wind turbine. The length, thickness, and chord length of the blade were 3m, 0.36m, and 0.12 m respectively. Computational Fluid Dynamics was used to develop to obtain lift and drag coefficients in a horizontal wind turbine blade. In addition, the correlation between different angles of attack, lift, and drag forces were studied and validated. The results demonstrated that the lift and drag coefficients increase as the angle of attack increases. Furthermore, the optimal angle of attack for this study was 0° because it has the highest lift-to-drag ratio, resulting in the greatest efficiency. The results demonstrated that it is possible to have a different lift and drag coefficient for the same angles of attack at a similar airfoil.

15 October 2024
Verified
Book Chapter
Closed access
PDF file
MKMorteza Khashehchi
Morteza Khashehchi
MHMilad Heidari
Milad Heidari
STSivasakthivel Thangavel
Sivasakthivel Thangavel
PRPooyan Rahmanivahid
Pooyan Rahmanivahid
Ashwani KumarAshwani Kumar
Ashwani Kumar
YSYogesh Kumar Singla
Yogesh Kumar Singla

27 May 2021 in TEM Journal
Verified
Journal Article
Open access
KAKiumars Khani Aminjan
Kiumars Khani Aminjan
MHMilad Heidari
Milad Heidari
PRPooyan Rahmanivahid
Pooyan Rahmanivahid
HAHouman Alipour
Houman Alipour
MKMorteza Khashehchi
Morteza Khashehchi