In the final process of the bleached kraft pulp there are some cellulose fibers that are separated from the main fibers stream; these fibers are rejected and considered as a low quality fibers, these fibers are known as rejected fiber (RF). In the present work the potential use of these fibers for Cellulose Nanocrystals (CNCs) synthesis was studied. The physical and chemical properties of synthesized CNCs were characterized through different techniques such as Atomic Force Microscopy (AFM), Scanning Electron Microscopy (SEM), X-Ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FTIR), and Thermogravimetric Analysis (TGA). Results demonstrate the feasibility of CNCs synthesis with a yield of 28.1% and 36.9%, and crystallinity of 73.5% and 82.7%. Finally, the morphology and synthesis conditions suggest that this industrial reject fiber (RF) could be used as a source for the CNCs production, thus adding value to the kraft process and opening new possibilities for innovation in the pulp industry.

We study the questions of existence and uniqueness of non-negative solutions to the Cauchy problem $\rho(x)\partial_t u= \Delta u^m\qquad$ in $Q$:$=\mathbb R^n\times\mathbb R_+$ $u(x, 0)=u_0$ in dimensions $n\ge 3$. We deal with a class of solutions having finite energy $E(t)=\int_{\mathbb R^n} \rho(x)u(x,t) dx$ for all $t\ge 0$. We assume that $m> 1$ (slow diffusion) and the density $\rho(x)$ is positive, bounded and smooth. We prove existence of weak solutions starting from data $u_0\ge 0$ with finite energy. We show that uniqueness takes place if $\rho$ has a moderate decay as $|x|\to\infty$ that essentially amounts to the condition $\rho\notin L^1(\mathbb R^n)$. We also identify conditions on the density that guarantee finite speed of propagation and energy conservation, $E(t)=$const. Our results are based on a new a priori estimate of the solutions.

We use dry-jet wet spinning in a coaxial configuration by extruding an aqueous colloidal suspension of oxidized nanocellulose (hydrogel shell) combined with airflow in the core. The coagulation of the hydrogel in a water bath results in hollow filaments (HF) that are drawn continuously at relatively high rates. Small-angle and wide-angle X-ray scattering (SAXS/WAXS) reveals the orientation and order of the cellulose sheath, depending on the applied shear flow and drying method (free-drying and drying under tension). The obtained dry HF show Young's modulus and tensile strength of up to 9 GPa and 66 MPa, respectively. Two types of phase-change materials (PCM), polyethylene glycol (PEG) and paraffin (PA), are used as infills to enable filaments for energy regulation. An increased strain (9%) is observed in the PCM-filled filaments (HF-PEG and HF-PA). The filaments display similar thermal behavior (dynamic scanning calorimetry) compared to the neat infill, PEG, or paraffin, reaching a maximum latent heat capacity of 170 J·g^-1 (48-55 °C) and 169 J·g^-1 (52-54 °C), respectively. Overall, this study demonstrates the facile and scalable production of two-component core-shell filaments that combine structural integrity, heat storage, and thermoregulation properties.

Direct ink writing via single or multihead extrusion is used to synthesize layer-by-layer (LbL) meshes comprising renewable polysaccharides. The best mechanical performance (683 ± 63 MPa modulus and 2.5 ± 0.4 MPa tensile strength) is observed for 3D printed structures with full infill density, given the role of electrostatic complexation between the oppositely charged components (chitosan and cellulose nanofibrils). The LbL structures develop an unexpectedly high wet stability that undergoes gradual weight loss at neutral and slightly acidic pH. The excellent biocompatibility and noncytotoxicity toward human monocyte/macrophages and controllable shrinkage upon solvent exchange make the cellular meshes appropriate for use as biomedical implants.

In the last years, Chile has increased the production of blueberries; consequently, a large number of lignocellulosic residues derived from the harvesting and pruning are being generated. These residues are commonly burned, therefore increasing CO₂ emissions. This study focuses on the extraction of two added-value products from blueberry pruning residues (BPRs), cellulose nanocrystals (CNC-IL) isolated using ionic liquid (IL) 1-ethyl-3-methylimidazolium [emim][Cl], and carboxylated nanocellulose (TOCNC), isolated with (2,2,6,6-tetramethylpiperidine-1-yl) oxyl or TEMPO reagent combined with a mechanical disintegration process. These products were characterized by zeta potential (ζ), FTIR, XRD, TGA, AFM, and conductometric titration. Results show oval-shaped CNC-IL particles with lengths of 46.1 ± 9.3 nm; meanwhile, TOCNC were rod-like shaped particles, with lengths of 120.3 ± 30.6 nm. These BPRs showed a promising potential to produce cellulose nanocrystals (CNCs) with different surface properties, opening a new alternative for the production of cellulose nanomaterials (CNMs) with promising applications in colloidal formulations, coatings, among others.