Sri Mulyo Bondan Respati

Dr. Sri Mulyo Bondan Respati

orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 July 2021 in Mechanical Engineering for Society and Industry
Verified
Journal Article
Open access
PDF file
SRSri Mulyo Bondan Respati
Sri Mulyo Bondan Respati
HPHelmy Purwanto
Helmy Purwanto
IFIlham Fakhrudin
Ilham Fakhrudin
PPPungkas Prayitno
Pungkas Prayitno
The growth of the textile industry and the massive use of plastic-based materials create economic growth, but it produces waste from post-use, such as clothing waste from cotton fabrics and HDPE that can be recycled and combined as composite materials. Therefore, an experiment was carried out to investigate and analyze the effect of the fiber volume fraction of waste cotton fabric (1.5%, 3.5%, 4.5%, 6%, and 7.5%) with straight fiber arrangement on the tensile strength and density. From the test results, a tensile strength of 178.4 MPa and 182.6 MPa was obtained for yield and max stress, respectively at a fiber volume fraction of 7.5%. Meanwhile, the highest density of 0.95 g/cm3 was obtained at 1.5% fiber volume fraction. The fracture macroscopic view of the specimen shows a resilience fracture (uneven and appears stringy). Although the strength of this composite cannot yet compete with the new composite material, it has a decent environmental contribution. Considering the availability of waste cotton fabrics and HDPE, it promises to be produced as a low-strength composite for construction, ornamentation, or coatings.

26 June 2018 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
SRSri Mulyo Bondan Respati
Sri Mulyo Bondan Respati
RSRudy Soenoko
Rudy Soenoko
YIYudy Surya Irawan
Yudy Surya Irawan
WSWahyono Suprapto
Wahyono Suprapto
DWDenny Kristianto Wicaksono
Denny Kristianto Wicaksono
HPHelmy Purwanto
Helmy Purwanto
The manufacture of porous ceramic membrane based on natural zeolite and palm fibers was done. Zeolite powders were sieved using 80 mesh and 120 mesh sieves. Moreover, the size was in the range from 80 mesh to below 120 mesh. It was mixed with palm fibers with diverse percentages of 0%, 5%, 10%, 15%, and 20% wt palm fibers. Preparation of mixing raw materials used ball mill to obtain evenly mixed powder. Ceramics were made through sintering process at temperature of 900°C, heating rate of 5°C/min, and holding time of 2 hours. This membrane ceramic is expected to decrease the TDS value. The recorded data included volume, weight, hardness, water discharge, and value of TDS (Total Dissolved Solids). Measurement of volume and weight used the Archimedes’ principle. The results of this study showed that the addition of palm fibers could decrease the density, increase the porosity. The highest hardness was obtained by specimen with the 5% wt fibers, with the higher water discharge and the lower TDS value.

8 October 2020 in Jurnal Teknik Mesin
Verified
Journal Article
Open access
PDF file
SRSri Mulyo Bondan Respati
Sri Mulyo Bondan Respati
IKIbnu Katsir
Ibnu Katsir
MDMuhammad Dzulfikar
Muhammad Dzulfikar
Body mobil KMHE yang dilombakan oleh kemendikbud tahunan, kebanyakan menggunakan rangka aluminium. Penelitian ini mengajukan bahan carbon fiber-honeycomb sebagai pengganti rangka aluminium. Dalam penelitian metode yang digunakan adalah melapisi honeycomb dengan lapisan carbon fiber-resin. Cara pelapisan bagian dari 1 sampai 3 lapisan pembuatan material menggunakan hand lay-up. Standar specimen yang digunakan adalah ASTM D 638-02 dan ASTM D 790 – 02. Hasil penelitian ini menunjukan bahwa berturut-turut kekuatan tarik dan bending tertinggi di dapat pada 3 lapisan atas komposit karbon fiber-honeycomb 3449,49 kg/mm2 dan untuk pengunjian bending 203,65 kg/mm2. Jika dibandingkan dengan aluminium maka bahan ini dapat digunakan sebagai body mobil KMHE

23 April 2022 in Automotive Experiences
Verified
Journal Article
Open access
PDF file
SSSuntari Suntari
Suntari Suntari
HPHelmy Purwanto
Helmy Purwanto
SRSri Mulyo Bondan Respati
Sri Mulyo Bondan Respati
SSSugiarto Sugiarto
Sugiarto Sugiarto
ZAZainal Abidin
Zainal Abidin
This study evaluates the macrostructure, microstructure, hardness, and tensile strength in dissimilar metal welding applied to bus body construction. The process involved joining hollow stainless steel and galvanized steel at the dimensions of 80 x 40 x 3.2 mm through Gas Metal Arc Welding (GMAW). The current was varied at 90, 100, and 110 A while ER70S-6 electrodes with diameters of 0.8 and 1.0 mm were used. The results showed that electrode diameter and welding current affect the capping area, penetration depth, and hardness. Moreover, the formation of the widmasatten ferrite phase was increased and the coarse grain boundaries in the weld zone were detected. It was also observed that an increase in the diameter of the electrode and the welding current which indicates an increment in the heat reduced the rate of solidification and cooling. The average tensile strength for all the samples investigated was found to be lower than the value for the base metal. Therefore, further research is recommended to improve the tensile strength.

7 June 2017 in MM Science Journal
Verified
Journal Article
Open access
SRSri Mulyo Bondan Respati
Sri Mulyo Bondan Respati
RSRudy Soenoko
Rudy Soenoko
YIYudy Surya Irawan
Yudy Surya Irawan
WSWahyono Suprapto
Wahyono Suprapto
BSBudi Saputra
Budi Saputra
HPHelmy Purwanto
Helmy Purwanto

5 March 2018 in Matéria (Rio de Janeiro)
Verified
Journal Article
Open access
PDF file
SRSri Mulyo Bondan Respati
Sri Mulyo Bondan Respati
RSRudy Soenoko
Rudy Soenoko
YIYudy Surya Irawan
Yudy Surya Irawan
WSWahyono Suprapto
Wahyono Suprapto
Natural zeolite ceramic is a material that can be used as bioceramics but it is fragile to crack. The weakness of ceramics can be overcome by making ceramic metals. The use of SS316 (stainless steel 316) fiber to strengthen the zeolite ceramic had been done in order to determine the interfacial relationship by using a fiber pull-out test. The content of SS316 fiber in the zeolite ceramic matrix, before and after the sintering, had been examined by using atomic absorption spectrum tests. The content of the elements in SS316 fiber, zeolite ceramic matrix and the interface layer was became clear by using EDX and XRD test. The results showed that the higher the sintering temperature, the higher the interfacial shear stress on pull-out test as well. However, at a temperature of 900°C, the interfacial shear stress on pull-out test became low because of the Fe, FeNi, and CrFe was arisen in a thin layer of the interface. The optimum of the temperature sintering for making ceramic zeolite matrix and SS16 fibers was 850°C because of the highest interfacial shear stress.