Accurately simulating the thermal behavior of wheel–brake shoe friction on long downhill ramps is challenging due to the complexity of modeling appropriate heat source models. This study investigates heat generation during the frictional braking process of freight train wheels and brake shoes under long-slope conditions. Four heat source models—constant, modified Gaussian, sinusoidal, and parabolic distributions—were developed based on energy conservation principles and validated through experimental data. A thermomechanical coupled finite element model was established, incorporating a moving heat source to analyze the effects of different models on wheel tread temperature distribution and its evolution over time. The results show that all four models effectively simulate frictional heat generation, with computed temperatures, deviating by only 6.0–8.2% from experimental measurements, confirming their accuracy and reliability. Among the models, the modified Gaussian distribution heat source, with its significantly higher peak local heat flux (2.82 times that of the constant model) and rapid attenuation, offers the most precise simulation of the non-uniform temperature distribution in the contact region. This leads to a 40% increase in the temperature gradient variation rate and effectively reproduces the “hot spot” effect. The new non-uniform heat source model accurately captures local temperature dynamics and predicts frictional heat transfer and thermal damage trends. The modified Gaussian distribution model outperforms others in simulating local temperature peaks, offering support for optimizing braking system models and improving thermal damage prediction. Future research will refine this model by incorporating factors like material wear, environmental conditions, and dynamic contact characteristics.
To identify and diagnose the latent leakage faults of key pneumatic units in the Chinese standard Electric Multiple Units (EMU) braking system, a multi-source information fusion method based on Kalman filtering, sequential probability ratio test (SPRT), and support vector machine (SVM) is proposed. The relay valve is taken as an example for research. Firstly, Kalman’s state estimation function is used to obtain the innovation sequence, and the innovation sequence is input into the SPRT model to help recognize latent leakage faults of the relay valve. Using this method, the problem of the incomplete training set of the traditional SPRT method due to the change of the braking level and the vehicle load is solved. Secondly, the eight time-domain parameters of the relay valve input and the output pressure signal are extracted as fault characteristics, and then input to the support vector machine to realize the internal and external leakage fault diagnosis of the relay valve, which provides a reference for maintenance. Finally, this method is verified by the fault simulation data by quickly identifying latent leakage faults and diagnosing the internal and external leakage at a fault recognition rate of 100% by SVM under small sample conditions.
During the service life of brake systems, performance degradation of the components is inevitable. In order to grasp the health status of components of brake systems, and aiming at the problem that the performance degradation trend of the components of the brake system is not completely clear due to signal coupling between components, the influence of variable working conditions, and the long performance degradation cycle, a performance degradation prognosis method of the components of the brake system based on relative characteristic (RC) and the long short-term memory (LSTM) network was proposed. The input and output signals of the components were isolated and fused, the working condition-independent RC was extracted to construct the health indicator (HI), and the validity of the HI was tested by using the monotonicity, correlation, and robustness metrics. Moreover, considering the time memory characteristics, the trend prediction of the HI curve of the components of the brake system was carried out based on the LSTM network. Furthermore, data augmentation for the training and testing sets was performed. Taking the typical component of brake systems as an example, a performance degradation test was carried out. The analysis results of the test data show that the accuracy of the performance degradation prognosis of the intake filter was over 99%, which validates the effectiveness and accuracy of the proposed method. The research results could provide a reference for health management and to improve the active safety protection capability of brake systems of in-service trains.
Due to the difference in gradient resistance between the front and rear vehicles, the long marshalling train will produce a larger longitudinal impulse when it passes through the gradient change point for blend braking. The conventional strategy of simultaneous application of dynamic and air braking and average distribution of dynamic braking is not necessarily optimal, it is significant to optimize in-train longitudinal forces under the target braking performance through the different blend braking strategy for heavy haul train. Firstly, mathematical models of in-train longitudinal forces are developed for longitudinal train dynamic simulations including the air braking system sub-model with the brake delay time and multi-stages nonlinear charging characteristics and the friction draft gear sub-model with the viscous resistance characteristics. Besides, longitudinal dynamic simulation is conducted to study and analyze the dynamic braking matching strategy in a typical case when “1+1+1” 20,000-ton train passes through the gradient change point of “-12‰ downhill-straight track” for blend braking. The influence of different dynamic braking distribution and asynchronous application strategy on the longitudinal impulse of the train is analyzed. Finally, a particle swarm optimization algorithm is proposed to achieve rapid optimization of the optimal locomotive dynamic braking distribution. This work provides valuable insights into simulating in-train longitudinal forces to realize the safe and efficient operation of heavy haul trains in the future.
22 December 2023 in Advances in Mechanical Engineering
In order to prognose the performance for air brake systems of in-service trains, a data augmentation method based on correlation analysis and improved multivariate support vector regression was proposed in this paper. By using black box theory and correlation analysis, brake cylinder pressure was extracted as the performance identification signal of air brake system, and the input and output signals were used as the auxiliary signals to construct the black box model of air brake system. Meanwhile, in order to make full use of the obtained data information, a data augmentation prognosis model based on improved multivariate support vector regression was established. Moreover, the optimal parameters of prognosis model were selected by means of particle swarm optimization algorithm, and RMSE and MAE were used as evaluation indicators. Finally, case studies on test-rig performance experiment data of air brake system were conducted. The prognosis model was trained and verified by using the service 1-7N and emergency, service full brake-relief and stage brake-relief experiment data, respectively, and the modeling and calibration error at pressure-holding stage were both in the order of ±5 kPa, which demonstrated the proposed method to be quite accurate and effective.