This paper proposes the design of an aerodynamic braking device for a high-speed train. The design is based on the parameters of the high-speed train and the working principles of airplane wings. The proposed device is a unidirectional opening model driven by hydraulics. The prototype uses hard-wired signals to transmit braking commands on eight levels. The important characteristics of the device include a synchronous action and a fault-oriented security design. Its functions include service braking, gradual braking, emergency braking and self-checking. Simulation results show that deceleration in the high-speed zone between 250 and 500 km/h can be improved by between 8 and 60%. When the train runs at 500 km/h, the braking deceleration rate can be improved by 0.12 m/s2. The simulation results are found to agree with wind tunnel test results. The braking characteristics are also investigated using a test bed, which mimics the aerodynamic load exerted on the prototype when the train is running between 0 and 550 km/h. It is clearly demonstrated that the proposed principle of the aerodynamic braking system is feasible and its design scheme is reasonable. The aerodynamic braking device can survive a 50,000 N aerodynamic load, and the time taken to achieve the maximum braking capacity, which is the time taken to take the brake panel from its closed position of −5° to the maximum angle of 75°, is less than 3 s. The proposed prototype therefore offers an important step in the design of practical systems.
20 May 2014 in Journal of Mechanical Science and Technology
The rail temperature rises when the linear eddy current brake of high-speed train is working, which may lead to a change of rail physical characteristics or an effect on train operations. Therefore, a study concerning the characteristics of rail temperature rise caused by eddy current has its practical necessity. In the research, the working principle of a linear eddy current brake is introduced and its FEA model is established. According to the generation mechanism of eddy current, the theoretical formula of the internal energy which is produced by the eddy current is deduced and the thermal load on the rail is obtained. ANSYS is used to simulate the rail temperature changes under different conditions of thermal loads. The research result shows the main factors which contribute to the rising of rail temperature are the train speed, brake gap and exciting current. The rail temperature rises non-linearly with the increase of train speed. The rail temperature rise curve is more sensitive to the exciting current than the air gap. Moreover, the difference stimulated by temperature rising between rails of 60kg/m and 75kg/m is presented as well
Accurately simulating the thermal behavior of wheel–brake shoe friction on long downhill ramps is challenging due to the complexity of modeling appropriate heat source models. This study investigates heat generation during the frictional braking process of freight train wheels and brake shoes under long-slope conditions. Four heat source models—constant, modified Gaussian, sinusoidal, and parabolic distributions—were developed based on energy conservation principles and validated through experimental data. A thermomechanical coupled finite element model was established, incorporating a moving heat source to analyze the effects of different models on wheel tread temperature distribution and its evolution over time. The results show that all four models effectively simulate frictional heat generation, with computed temperatures, deviating by only 6.0–8.2% from experimental measurements, confirming their accuracy and reliability. Among the models, the modified Gaussian distribution heat source, with its significantly higher peak local heat flux (2.82 times that of the constant model) and rapid attenuation, offers the most precise simulation of the non-uniform temperature distribution in the contact region. This leads to a 40% increase in the temperature gradient variation rate and effectively reproduces the “hot spot” effect. The new non-uniform heat source model accurately captures local temperature dynamics and predicts frictional heat transfer and thermal damage trends. The modified Gaussian distribution model outperforms others in simulating local temperature peaks, offering support for optimizing braking system models and improving thermal damage prediction. Future research will refine this model by incorporating factors like material wear, environmental conditions, and dynamic contact characteristics.
To identify and diagnose the latent leakage faults of key pneumatic units in the Chinese standard Electric Multiple Units (EMU) braking system, a multi-source information fusion method based on Kalman filtering, sequential probability ratio test (SPRT), and support vector machine (SVM) is proposed. The relay valve is taken as an example for research. Firstly, Kalman’s state estimation function is used to obtain the innovation sequence, and the innovation sequence is input into the SPRT model to help recognize latent leakage faults of the relay valve. Using this method, the problem of the incomplete training set of the traditional SPRT method due to the change of the braking level and the vehicle load is solved. Secondly, the eight time-domain parameters of the relay valve input and the output pressure signal are extracted as fault characteristics, and then input to the support vector machine to realize the internal and external leakage fault diagnosis of the relay valve, which provides a reference for maintenance. Finally, this method is verified by the fault simulation data by quickly identifying latent leakage faults and diagnosing the internal and external leakage at a fault recognition rate of 100% by SVM under small sample conditions.
28 April 2012 in Chinese Journal of Mechanical Engineering
In modern trains wheelset skidding leads to the deterioration of braking behavior, the degradation of comfort, as well as a boost in system hazards. Because of the nonlinearity and unknown characteristics of wheelset adhesion, simplifications are widely adopted in the modeling process of conventional antiskid controllers. Therefore, conventional antiskid controllers usually cannot perform satisfactorily. In this paper, systematic computer simulation and field tests for railway antiskid control system are introduced. The operating principal of antiskid control system is explained, which is fundamental to the simulation of antiskid brakes, and the simulation model is introduced, which incorporates both the adhesion creep curve and a pneumatic submodel of antiskid control system. In addition, the characteristics of adhesion curves and the simulation target are also provided. Using DHSplus, the pneumatic submodel is created to analyze the performance of the different control strategies of antiskid valves. Then the system simulation is realized by combining the kinematical characteristics of railway trains and the pneumatic submodel. The simulation is performed iteratively to obtain the optimized design of the antiskid control system. The design result is incorporated in the hardware design of the antiskid control system and is evaluated in the field tests in Shanghai Subway Line 1. Judging by the antiskid efficiency, the antiskid braking performance observed in the field tests shows the superiority of the optimized design. Therefore, the proposed simulation method, especially in view of its ease of application, appears to be a useful one for designing railway antiskid control systems.