Hongping Zhang

Dr. Hongping Zhang


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 November 2019 in Arabian Journal for Science and Engineering
Verified
Journal Article
Closed access
PDF file
HZHongping Zhang
Hongping Zhang
PBPei-Kang Bai
Pei-Kang Bai
JWJian-Hong Wang
Jian-Hong Wang
YDYan-Li Dong
Yan-Li Dong

26 November 2021 in Journal of Advanced Concrete Technology
Verified
Journal Article
Closed access
PDF file
HZHongping Zhang
Hongping Zhang
JWJianhong Wang
Jianhong Wang
YLYaling Liu
Yaling Liu
XZXiangshuang Zhang
Xiangshuang Zhang
The study aims to solve the problem that the concrete suitable for three-dimensional (3D) printing achieves more working performances, while the mutual influence, crossover, and contradiction among the working performances. In this study, a multi-index evaluated, gradual-optimized test based working performance is proposed. First, the concrete proportions satisfying 3D printing were obtained through orthogonal test and then gradually optimized systematically to the proportions determined by conducting an orthogonal experiment. The correlation between assessment indexes was analyzed. The test results show that fluidity and thixotropic sensitivity can be combined to evaluate comprehensively the work performance of 3D-printed concrete. The flow rate can further optimize the mix ratio, and the correlation between stacking height and number of extruded layers is weak. Moreover, the building performance of 3D-printed concrete can be evaluated from the number of layer and deformation of concrete to optimize the concrete ratio further. The suitable fluid range for 3D-printed concrete is 17.7-20.0 cm, and the corresponding stacking height is 45-57 mm. The successfully printed building components from the optimized concrete proportion further verify that the test method used in this study is reasonable and scientific, and that it can be extended to prepare other concretes satisfying more performance.

11 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
LLLan Liu
Lan Liu
YLYuhao Liu
Yuhao Liu
ZCZhi Cheng
Zhi Cheng
XCXinrong Cheng
Xinrong Cheng
HZHongping Zhang
Hongping Zhang
Desulfurization slag (DS) is the solid waste discharged from the bottom of the circulating fluidized bed (CFB) boiler. It has good pozzolanic activity, self-hardening property and large expansibility. In this paper, ground desulfurization slag (GDS) is used as mineral admixture to replace cement to prepare self-compacting concrete (SCC). In order to find out the influence laws of different factors on the axial compressive properties of the self-compacting concrete filled steel tube (CFST), seven types of SCC are prepared and nine groups of CFST short column are fabricated. Filling ability test, compressive strength test and axial compressive test are performed. The filling ability and the compressive strength of the SCCs are investigated, and the axial compressive properties of the CFSTs are researched. The results show that the amount of polycarboxylate superplasticizer (PS) increases with the amount of GDS, and the addition of GDS decreases the 3d, 7d and 28d compressive strength of the SCCs. The optimum amount of GDS for SCCs and CFSTs is 30%. When the amount of GDS is 30%, the ultimate bearing capacity of CFST short column (GP3) is the highest, which is 33.6% higher than that of GP1 without GDS. The influence law of the GDS’s amount on the CFSTs’ ultimate bearing capacity is quite different from that of the GDS’s amount on the SCCs’ compressive strength. The ultimate bearing capacity of CFSTs can be significantly improved by adding GDS. Sodium sulfate can improve both the compressive strength of the SCC and the bearing capacity of the CFST.

26 July 2022 in Materials Letters
Verified
Journal Article
Closed access
HZHongping Zhang
Hongping Zhang
YLYaling Liu
Yaling Liu
ZCZhi Cheng
Zhi Cheng
ZZZhiyi Zhao
Zhiyi Zhao

6 January 2019 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
HZHongping Zhang
Hongping Zhang
PBPei-Kang Bai
Pei-Kang Bai
JWJian-Hong Wang
Jian-Hong Wang
YDYan-Li Dong
Yan-Li Dong
YHYun-Shan Han
Yun-Shan Han
In this work, we propose the use of steel slag instead of slag powder, in addition to fly ash and silica fume, to obtain high-performance sulphoaluminate cement-based materials. According to the closest-packing theory and on the basis of the minimum water requirement test, the influence of mineral admixtures on the minimum water requirement was evaluated for sulphoaluminate composite system paste. The optimal composition of the cementitious materials was thus determined. Orthogonal tests were used to assess the validity of this ratio. The correlation between minimum water requirement and the standard consistence was not only analyzed in the system of the minimum water requirement method decided but also in the complicate system of the orthogonal tests determined. Experimental results show that the influence of steel slag on the minimum water requirement is the largest in composite cement paste; minimum water requirement and standard consistency have a good correlation; the cement paste designed with the optimum composite had the highest strength of all the tested materials, but minimum water requirement and strength have a poor correlation in the orthogonal tests. We demonstrate that standard consistency evaluation can replace the minimum water requirement method to determine the optimum ratio of cement mineral admixtures. The proposed method not only simplifies the process but also makes the method more scientific.

26 March 2024 in JOM
Verified
Journal Article
Closed access
PDF file
HZHongping Zhang
Hongping Zhang
SDShuni Duan
Shuni Duan
QHQi Han
Qi Han
QHQiangqiang He
Qiangqiang He
ZSZiteng Shi
Ziteng Shi
SQShuwei Qu
Shuwei Qu