In this study, our aim is to investigate the structural, magnetic, and magnetocaloric properties of the FeNi binary alloy. The FeNi alloy with Fe65Ni35 composition was prepared by ball milling followed by the annealing and quenching processes. A Rietveld refinement analysis of structural results reveals that this system has coexisting cubic structural phases with a dominant face-centered cubic phase (Fm-3m;γ-FeNi). Magnetization results of this compound indicate the presence of ferromagnetic ordering and the magnetic transition observed around 100 K. Moreover, an Arrott plot study provides information about the order of phase transition, which is found in the second-order near the ordering temperature, whereas first-order nature is also noted in the low-temperature region. The significant magnetocaloric parameters, i.e., magnetic entropy change (ΔSM~0.495 J/kg-K) and relative cooling power (88 J/kg), are noted over a wide temperature range. The power law dependency of magnetic entropy change with the applied field is also investigated. Due to their significant magnetocaloric performance over a wide temperature range, these multiphase alloys may be a good candidate for room-temperature to low-temperature magnetic refrigeration.
Iron-transition metal-based binary and ternary alloys have attracted great attention due to their relevant mechanical, electrical, and magnetic properties. In this paper, we systematically investigate the structural, magnetic, and magnetocaloric behavior of as-milled Fe65T35 (T = Ni and Mn) alloy. The polycrystalline alloys were produced by the planetary ball milling, using a powder-to-ball ratio of 1:3. A structural study reveals that both Fe65Ni35 and Fe65Mn35 compounds have stabilized in α and γ mixed phase within the cubic crystal structure. The alloyed compounds are further characterized by high-resolution field emission scanning electron microscopy (HR-FESEM), which confirms the mixing of both metals in the alloying process. Temperature-dependent magnetic studies do not show any blocking in zero-field-cooled and field-cooled results; however, the field-dependent magnetization study demonstrates the ferromagnetic nature with small hysteresis in both compounds. Both compounds show a significant magnetocaloric effect over a wide temperature range around room temperature. Fe65Ni35 exhibit a slightly higher value in comparison to Fe65Mn35. In both the alloys, magnetic entropy change follows the power law behavior against the external magnetic field, and the value of exponent ‘m’ explains the presence of magnetic correlation. Our investigation in this study communicates that the phase control or coexistence of both phases may be efficacious in obtaining the desirable characteristic of magnetic and magnetocaloric demeanors in such a binary Fe-T alloy.
The multifunctional attributes of SmFeO3 make it a promising candidate for the current diverse technological applications. Therefore, in this work, we investigated the effect of synthesis temperature on the magnetic, optical and electrochemical properties of SmFeO3 nanoparticles at room temperature (SFO-RT) and 50 °C (SFO-50) when prepared through the co-precipitation method. The XRD analysis revealed two distinct phases: SmFeO3 and Sm2O3 as secondary with SmFeO3 emerging as the primary phase (88–93%). The FESEM images showed the amalgamated morphology of the nanoparticles indicating the enhanced thermal kinetics of the solution which not only limited the particle growth but also facilitated their coalition. The band gap energy was found to be 2.2 and 2.3 eV for SFO-RT and SFO-50, respectively, while the values of saturation magnetization noted were 2.14 and 1.53 emu/g for SFO-RT and SFO-50, respectively. The XPS analysis revealed Sm to be in a +3 oxidation state, while Fe was in a mixed (+3/+2) oxidation state showing an increase in the ionic concentration in SFO-50. From the electrochemical measurements, the highest specific capacitance was observed for SFO-50 (65.8 F/g) as compared to SFO-RT (49.3 F/g). The results indicate a clear effect of synthesis temperature on the properties of SmFeO3. Here, two factors played a prominent role: one was the morphology, shaped through the particle growth, and the other was the secondary phase. The decrease in the size of the agglomerated particles and phase fraction of the secondary phase brought about necessary changes in the structural attributes to reduce the saturation magnetization and enhance the specific capacitance of SFO-50. Overall, this study shows that the synthesis temperature affects the crystalline structure and phase fractions leading to the modulation of electronic structure, band gap, magnetic interactions and specific capacitance.
A hybrid cationic system comprising bio-based chitosan and synthetic branched polyethyleneimine (BPEI) was employed to facilitate the flame-retardant deposition of halloysite nanotubes (HNTs) onto cotton fabrics through a layer-by-layer (LbL) assembly process. The FTIR results revealed new peaks of O-H stretching and Si-O-Si groups on halloysite nanoclay at the respective positions of 3699.84 cm−1, 3625.60 cm−1, and 527.57 cm−1, which suggests successful layering of the anionic species. From surface microstructural analysis, bridging features between adjacent fibers of coatings were found; however, an increase in homogeneity and randomness was also observed as the number of layers increased. Thermogravimetric analysis further exposed that the incorporation of nanoclay tubes engenders substantial char residue at 700 °C up to 32.98%, while the decomposition rate decreased from 0.235% to 0.149%. Additionally, the flame-retardant properties were rigorously assessed using a vertical flame test: self-extinguishment behavior emerged in the C-25 and C-30 coated samples, while the other samples effectively resisted flame propagation. The results confirm the effectiveness of hybrid flame-retardant coating and offer a sustainable strategy for eliminating reliance on hazardous chemical additives.