As compared to China’s overall oil reserves, the reserve share of offshore oilfields is rather significant. However, offshore oilfield circumstances for enhanced oil recovery (EOR) include not just severe temperatures and salinity, but also restricted space on offshore platforms. This harsh oil production environment requires polymers with relatively strong salt resistance, solubility, thickening ability, rapid, superior injection capabilities, and anti-shearing ability. As a result, research into polymers with high viscosity and quick solubility is recognized as critical to meeting the criteria of polymer flooding in offshore oil reservoirs. For the above purposes, a novel hydrophobically associating polymer (HAP) was prepared to be used for polymer flooding of Bohai offshore oilfields. The synthetic procedure was free radical polymerization in aqueous solutions starting at 0 °C, using acrylamide (AM), acrylic acid (AA), 2-acrylamido-2-methylpropane sulfonic acid (AMPS), and poly(ethylene glycol) octadecyl methacrylate (POM) as comonomers. It was discovered that under ideal conditions, the molecular weight of HAP exceeds 2.1 × 10⁷ g⋅mol⁻¹. In a simulated reservoir environment, HAP has substantially greater solubility, thickening property, and salt resistance than conventional polyacrylamide (HPAM), with equivalent molecular weight. Finally, the injectivity and propagation of the two polymers in porous media were investigated. Compared with HPAM, which has a similar molecular weight, HAP solution with the concentration of 0.175% had a much better oil displacement effect in the porous medium, which can enhance oil recovery by 8.8%. These discoveries have the potential to pave the way for chemical EOR in offshore oilfields.

Supercritical multi-thermal fluid is an emerging and efficient heat carrier for thermal recovery of heavy oil, but the generation of supercritical multi-thermal fluid and its feasibility in thermal recovery are rarely discussed. In this paper, generation and flooding experiments of supercritical multi-thermal fluid were carried out, respectively, for the generation and feasibility of supercritical multi-thermal fluid. During the experiment, the temperature and pressure in the reactor and sand-pack were monitored and recorded, the fluid generated by the reaction was analyzed by chromatography, and enthalpy of the reaction product and displacement efficiency were calculated, respectively. The experimental results showed that the change in temperature and pressure in the reactor could be roughly divided into three stages in the generation process of supercritical multi-thermal fluid. The higher the proportion of oil in the reactant, the higher the maximum temperature in the reactor. When the proportion of oil and water in the reactant was constant, the temperature rise in the reactor was basically the same under different initial temperature and pressure conditions. Compared with the initial temperature and pressure, the oil–water ratio of the reactants had a significant effect on the generated supercritical multi-thermal fluid. The higher the proportion of oil, the more gas that was generated in the supercritical multi-thermal fluid, and the lower the specific enthalpy of the thermal fluid. Under the same proportion of oil and water, the gas–water mass ratio of the supercritical multi-thermal fluid generated by the reaction of crude oil was lower, and the specific enthalpy was higher. Through this study, it was found that supercritical multi-thermal fluid with a low gas–water mass ratio had higher oil displacement efficiency, higher early oil recovery rate, a larger supercritical area formed in the oil layer, and later channeling. The results of this study show that the optimal gas–water mass ratio of supercritical multi-thermal fluid was about 1, under which the oil displacement efficiency and supercritical area in the oil layer reached the maximum. Correspondingly, the optimal proportion of oil in the reactant when generating supercritical multi-component thermal fluid was about 10%. In oilfield applications, because the gas–water ratio in supercritical multi-component thermal fluid has a significant impact on oil displacement efficiency, the optimization of supercritical multi-thermal fluid should not only consider the generation process but also consider the oil displacement effect of the thermal fluid. The findings of this study could improve our understanding of the characteristics of generating supercritical multi-thermal fluid and the feasibility of supercritical multi-thermal fluid generated under different conditions in the oil displacement process. This research is of great significance for field applications of supercritical multi-thermal fluid.

Temporary plugging acidizing is a critical well stimulation technique for improving water absorption profiles and addressing low/zero water intake in individual intervals of heterogeneous reservoirs, serving as a core measure for production stabilization and enhancement in mature oilfields. However, there remains an urgent demand for balanced stimulation technologies tailored to the unique reservoir conditions of offshore water injection wells. In this study, targeting the reservoir characteristics of the target offshore oilfield, we systematically investigated the effects of Temporary Plugging Agent (TPA) concentration, acid injection slug size, injection rate, and permeability contrast on plugging and diversion performance. Three core innovations are achieved: (1) optimization of a high-strength self-diverting TPA; (2) development of a matched composite retarded acid system; (3) establishment of quantitative process parameter design methods for temporary plugging acidizing in heterogeneous reservoirs. Based on these, a high-strength balanced plugging removal technology for water injection wells was developed. This technology enables balanced stimulation of thin interbeds in offshore water injection wells with large vertical spans, long treatment intervals, and significant variations in reservoir properties and formation pressure, providing robust technical support for optimizing water absorption profiles, achieving precise layer-by-layer stimulation, and enhancing waterflood development efficiency.