To better understand the relationship between flow, mixing and reactions in the process of preparing PP/TiO2, a 3D numerical simulation in a co-rotating twin screw extruder (TSE) was firstly employed using commercial CFD code, ANSYS Polyflow. The effects of rotating speed of screws, stagger angle of knead blocks, inlet flow rate and initial temperature of barrel on the mixing and reaction process in the TSE were investigated. The results reveal that the studied operational and geometric parameters, which determine mixing efficiency, residence time distribution, and temperature of the flows in the TSE, affect the local species concentration, reaction time and reaction rate, and hence have great influences on the conversion rate. The results show that increasing the rotating speed and inlet flow rate can decrease the time for sufficient mixing, which is not conducive to intensive reaction, and increasing the stagger angle has the opposite effect. Moreover, the conversion rate greatly affected by the initial temperature of barrel.
22 March 2007 in Polymer-Plastics Technology and Engineering
The flow of polyethylene melt in new tri-screw extruder was simulated using the finite element method (FEM). A special study of flow in central region was performed by analysis of the velocity, pressure, and resident time distribution (RTD). The extrusion characteristics of tri-screw extruder, namely the abilities of material conveying, mixing, and power consumption, were compared with those of twin screw extruder. The results showed that there was circumfluence in central region but no stagnation in it. Tri-screw extruder had better operative abilities and high productivity ratio than twin screw extruder in the aspect of material conveying and mixing.
The four-screw extruder (FSE) is a novel equipment for polymer processing. In this paper, from a new viewpoint of Lagrangian coherent structures (LCS), two-dimensional fluid transport and chaotic mixing characteristics within three kinds of novel industrial FSEs are explored based on LCS to better understand the flow and mixing natures in the FSEs. Firstly, based on the finite-time invariant manifold theory, the finite-time Lyapunov exponent (FTLE) and LCS of FSEs are calculated by considering the different initial time. Hyperbolic LCSs from the FTLE maps are adopted to identify chaotic mixing manifolds in FSEs. Moreover, particle tracking and Poincaré sections are used to illustrate the different fluid motions in the above three isolated regions. Finally, the effects of relative rotating directions and layout of four screws on the chaotic manifolds in FESs are discussed in order to enhance local mixing performance. Furthermore, quantitative mixing measures, such as the segregation scale, logarithmic of stretching, and mean-time mixing efficiency are employed to compare the mixing efficiencies in three kinds of FSEs. The results show that the relative rotating directions and positions of four screws can change the chaotic manifolds and increase mixing performance in local poor mixing regions. FTLE and LCS analysis are helpful to better understand the chaotic mixing nature in the novel screw extruders.
The single-screw extruder with a perturbation baffle is a novel piece of equipment for polymer processing, in which the polymer melts undergo complex chaotic mixing. In this paper, from a new Lagrangian perspective, the fluid transporting mechanism in chaotic flow of the unwound screw channel was analyzed based on the finite element method. Firstly, two-dimensional velocity distributions in the unwound screw channel were calculated based on the mesh superposition technique. Fluid particle evolution processes in the extruder were tracked based on the fourth-order Runge-Kutta scheme. The numerical method used in this paper was validated by grid independence and experiments obtained from literature. Moreover, the finite-time Lyapunov exponent (FTLE) and Poincaré sections were adopted to discuss the chaotic mixing in the novel single-screw extruder. The effects of baffle width and height on the manifold structures in the flow dynamic system were analyzed. The results show that the homoclinic point of the manifold structure can give rise to chaotic mixing in the single-screw extruder. The height of the baffle is an important parameter to control the chaotic strength. In a way, increasing the height of the baffle can enlarge the kink scale and increase the stretching and folding actions, which results in the decrease of regular regions and an increase of the mixing efficiency in the single-screw extruder.
1 January 2013 in Engineering Applications of Computational Fluid Mechanics
A triangularly-arranged tri-screw extruder (TATSE) is a new piece of equipment for polymer processing, which has a dynamic center region. To learn about the special contributions of the dynamic center region and the circumfluence phenomenon just in cross section on the mixing mechanism of the TATSE, the 2D computational fluid dynamics (CFD) model was established to reduce the axial effect. The effects of screw clearances of the center region on mixing mechanism of the TATSE were studied. The mixing evaluations for the TATSE and twin-screw extruder (TSE) with different screw clearances were performed and compared. Moreover, the effects of different blend mass ratios of LLDPE and SBS on the mixing efficiency of the TATSE were studied. The results show that as screw clearances increase, the values of mean time-averaged and instantaneous efficiencies of the tri-screw extruder increase, but the normalized segregation scale decreases. The screw clearances even change the particle conditions from stretch to compression in the center region.
31 March 2009 in Polymer-Plastics Technology and Engineering
A triangle arrayed tri-screw extruder (TATSE) is a new-style extruder that has a special structure different from a twin screw extruder. Three-dimensional and non-isothermal flow in TATSE was simulated by using the finite element method. The temperature distribution, power consumption and productivity ratio in TATSE at various rotational speeds, screw flight number, pressure difference and flow rate were studied especially. Comparison and analysis of power consumption and productivity ratio between twin screw extruder (TSE), parallel arranged tri-screw extruder (PATSE) and TATSE were carried out. The results show that the mixing and power characteristics of TATSE are better than those of TSE and PATSE.