Comprehensive high-precision actuations are in growing demand to meet diversified needs in scientific and industrial fields. However, it is a great challenge for piezoelectric actuators with compact structure to guarantee high load capacity and wide velocity range (including fast motion velocity and high resolution) simultaneously. Herein, inspired by bionic methodology, a high-power-density bar-type linear piezoelectric ultrasonic actuator (LPUA) operating in the single second bending ( B2 ) mode with elaborate working principle is developed by imitating bicycle movement mechanism. The proposed B2 -LPUA actuator is simple and easy for miniaturization without multimodal decoupling problem. Under only one-phase voltage drive, the miniature bar-type actuator can produce continuously bidirectional motions with the maximum driving velocity, minimum driving velocity, load, and output power of 211.2 mm/s, 3.3 μ m/s, 5.4 N, and 218.3 mW, respectively, and the tested minimum step displacement is only 33 nm in open-loop control. Especially, its output power density (243 mW/cm 3 or 4.112 mW/cm 3 ⋅kHz) is at least twice larger than most reported LPUAs. The experimental results indicate that the proposed piezoelectric actuator with excellent actuation performances has broad application scenarios, and its bionic motion design method would have inspirational significance for creating new piezoelectric devices with more attractive properties.
1 December 2021 in Sensors and Actuators A: Physical
Fast actuation with nanoprecision over a large range has been a challenge in advanced intelligent manufacturing like lithography mask aligner. Traditional stacked stage method works effectively only in a local, limited range, and vibration coupling is also challenging. Here, we design a dual mechanism multimodal linear actuator (DMMLA) consisted of piezoelectric and electromagnetic costator and coslider for producing macro-, micro-, and nanomotion, respectively. A DMMLA prototype is fabricated, and each working mode is validated separately, confirming its fast motion (0~50 mm/s) in macromotion mode, micromotion (0~135 μ m/s) and nanomotion (minimum step: 0~2 nm) in piezoelectric step and servomotion modes. The proposed dual mechanism design and multimodal motion method pave the way for next generation high-precision actuator development.
Continual precision actuations with nanoscale resolution over large ranges have extensive requirements in advanced intelligent manufacturing and precise surgical robots. To produce continual nanostep motion, conventionally, multiple pairs of piezo‐actuators are employed to operate in inchworm principle under complex three‐ or four‐phase timing signal drive. Inspired by the idea of ordered structures with functional units, a much simpler nanostep piezoelectric actuator consisting of (2 × 2) arrayed, cofired multilayer piezoceramic actuation units is developed, which operates in an artificially generated quasi shear mode (AGQSM) that is missing in natural piezoelectric ceramics. Under only one‐phase square‐wave voltage drive, the actuator can produce a stable, continual nanostep motion in two ways at nonresonant frequencies, and the obtained minimum step displacement is as low as 7 nm in open control, indicating its potential application as a precise finger or knife actuator in surgical robots. This work is of great guiding significance for future actuator designs using the methodology of ordered structure with piezoceramic actuation units and AGQSM.
In this work, we report an enhanced magneto-mechano-electric (MME) coupling in Ni/Pb(Zr,Ti)O3 (PZT) ceramic composited ladder-type cantilever attached with a tip mass of NdFeB magnet, which simultaneously exhibits the magnetic flux concentration effect and the stress concentration effect, and therefore, it shows an enhanced extremely weak-field (EWF) coupling ability. Investigations show that the proposed MME energy harvester (EH) can generate an output power density of 7.16 μW Hz−1 Oe−2 cm−3, which is the highest value compared to the state of the art MME energy harvesters. Under an EWF of even as low as Hac = 0.1 Oe (about half level of the geomagnetic field), the proposed MME-EH can still produce a peak–peak output power of 23.5 μW, which is enough power to light up 4 LEDs in real time. Furthermore, it can drive a wireless sensor communication system in real time under a weak Hac = 0.75 Oe excitation, demonstrating it has potential to serve as a micro-energy source of wireless sensor networks in EWF circumstance. This work is not only beneficial but has also inspired future multi-function-integrated material and smart electronic device designs in Internet of Things in EWF circumstance.