Multi-level electron beam irradiation enabled bifunctional gradient grafting on silicon microspheres and rapid curing of silicone rubber coatings, allowing linear control of hydrophilicity and hydrophobicity.
Most lignin depolymerization products have specific functional groups and possess multiple reactivities, and therefore, have great potential to serve as starting materials for the synthesis of high value-added products. We describe herein an efficient strategy of using an oxidized lignin model compound, α-hydroxyacetophenone, as starting material to synthesize indoles or carbazoles in conjunction with using pyrroles or indoles as counterpart reagents. The reactions were performed using Sc(OTf)3 as a catalyst in a bio-based green solvent, glycerol, and moderate to excellent yields were obtained. At the end of the reaction, both solvent and catalyst can be recovered and reused. The novel approach presented here not only provides an eco-efficient route for the value-added conversion of lignin degradation products, but also extends the diversity of indole and carbazole derivatives, which are of potential importance in the development of functional photo-electric materials.
1 February 2023 in Review of Scientific Instruments
In this paper, a permanent-magnet-quadrupole doublet lens with strong-focusing is designed and manufactured. Such an instrument could solve the problem of irregular beam spots produced by the weak focusing of conventional solenoid-focusing systems in low-energy electron irradiation accelerators. It could provide a better and more appropriate initial beam spot before the beam enters the subsequent magnetic spreading system or magnetic scanning system, thus, improving the irradiation uniformity. The association of the parameters of the rectangular permanent magnet with the quadrupole magnetic field is investigated. Focusing results, obtained using irregular beam spots with different profiles and different energies, and magnetic field measurement results, both from the instrument, verify the engineering feasibility of this permanent-magnet-quadrupole doublet lens.
29 September 2023 in Physical Review Accelerators and Beams
The growing interest in the field of electron irradiation accelerators has led to various research opportunities, with a crucial emphasis on enhancing the irradiation homogeneity of accelerators to advance the industry of the irradiation process. In this study, we introduce a tunable and compact uniform spreading beamline that comprises a permanent magnet quadrupole doublet and an electron beam permanent magnet spreading system. This beamline could solve the problem of poor irradiation homogeneity caused by irregular beam spots in electron irradiation accelerators. Flexible and tunable magnetic yokes enable rapid changes to the magnetic field distribution based on different beam spot profiles or irradiation processing requirements, achieving uniform spreading of different beam spots and improving irradiation homogeneity. Additionally, we evaluated the performance of rectangular permanent magnet poles to minimize errors in future accelerator applications. The implementation of this beamline enhances irradiation quality and provides an experimental foundation for further investigating the interaction between electron beam irradiation rates and materials.
In this work, a permanent-magnet electron-beam-spread system for irradiation has been developed and constructed, and its performance was experimentally measured with a beam. This work is helpful to counter beam-tail sweep issues (resulting in excessive doses at the ends of each sweep). Using the beam’s optical transmission matrix and beam dynamics simulations, we analyzed the impact of the individual parameters of a special quadrupole magnet and a special octupole magnet on the beam spread, and we determined the optimal parameters for irradiation production. To meet the design requirements of the magnetic field, the yoke structure was optimized, and permanent magnets with very similar degrees of magnetization and small magnetic declinations were used. The permanent-magnet electron-beam-spread system was applied to an actual 0.5-MeV electron irradiation accelerator, and the engineering feasibility of the permanent magnet electron beam spread system was fully verified by measuring the uniformity of the beam after the spread.
Rosin- and castor-oil-derived resins provide a renewable platform for rapidly curable protective coatings, but the effects of formulation and curing route remain insufficiently resolved. Four composite formulations containing modified rosin glycerol ester (MRGE) and modified castor oil anhydride (MCOA) were cured thermally using ultraviolet irradiation or electron beam (EB) irradiation. Surface C=C conversion, thermal behavior, morphology, mechanical properties, neutral salt spray resistance, electrochemical barrier performance, and AC dielectric breakdown strength were evaluated. Among the formulations tested, F2 (MRGE/MCOA = 3:1) showed the best overall property balance under each curing route. For F2, EB curing produced a surface C=C conversion of 92 ± 2%, a glass transition temperature of 88 ± 1 °C, an 800 °C residue of 12.5 ± 0.3%, and an atomic force microscope (AFM) roughness Ra of 5.8 ± 0.5 nm. F2-EB exhibited 9H pencil hardness, 5B adhesion, an impact resistance of 55 ± 2 cm·kg, and a flexibility value of 1.0 ± 0.1 mm. After 500 h of neutral salt spray, both F2-EB and F2-UV achieved a protection rating of 10 with no measurable corrosion creep at the scribe; time-resolved photographs at 100, 300, and 500 h confirmed that F2-EB showed the least visible damage evolution among the three curing routes. After 1 day of immersion in 3.5 wt% NaCl, F2-EB exhibited the largest low-frequency impedance and the lowest fitted corrosion current density among the EB-cured formulations, indicating the strongest short-term electrolyte barrier behavior. The AC dielectric breakdown strength of F2-EB reached 21.5 ± 0.3 kV mm−1. The combined results are consistent with more extensive EB-induced network formation, although direct measurements of through-thickness conversion and crosslink density are still required. These findings demonstrate the potential of EB curing for rapidly preparing rosin/castor-oil-derived protective coatings for electrical insulation applications.