Pavana Prabhakar

Prof. Pavana Prabhakar

Department of Civil & Environmental Engineering, Department of Engineering Physics (Affiliate), University of Wisconsin-Madison, WI 53706, USA

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2015 in Additive Manufacturing
Verified
Journal Article
Closed access
PPPavana Prabhakar
Pavana Prabhakar
WSW.J. Sames
W.J. Sames
RDR. Dehoff
R. Dehoff
SBS.S. Babu
S.S. Babu

1 February 2018 in Composites Part B: Engineering
Verified
Journal Article
Closed access
Kiran ShahapurkarKiran Shahapurkar
Kiran Shahapurkar
CGCarlos D. Garcia
Carlos D. Garcia
MDMrityunjay Doddamani
Mrityunjay Doddamani
GKGC mohan Kumar
GC mohan Kumar
PPPavana Prabhakar
Pavana Prabhakar

1 October 2018 in Composites Part B: Engineering
Verified
Journal Article
Closed access
CGCarlos D. Garcia
Carlos D. Garcia
Kiran ShahapurkarKiran Shahapurkar
Kiran Shahapurkar
MDMrityunjay Doddamani
Mrityunjay Doddamani
GKGC mohan Kumar
GC mohan Kumar
PPPavana Prabhakar
Pavana Prabhakar

1 November 2018 in Materials & Design
Verified
Journal Article
Closed access
VDV. Damodaran
V. Damodaran
ACA.G. Castellanos
A.G. Castellanos
MMM. Milostan
M. Milostan
PPPavana Prabhakar
Pavana Prabhakar

15 January 2021 in Journal of Composites Science
Verified
Journal Article
Open access
PDF file
Alec RedmannAlec Redmann
Alec Redmann
VDVinay Damodaran
Vinay Damodaran
FTFelix Tischer
Felix Tischer
PPPavana Prabhakar
Pavana Prabhakar
Tim OsswaldTim Osswald
Tim Osswald
Adhesive bonding is increasingly being used for composite structures, especially in aerospace and automotive industries. One common joint configuration used to test adhesive strength is the single-lap shear joint, which has been widely studied and shown to produce significant normal (peeling) stresses. When bonding composite structures, the normal stresses are capable of causing delamination before the adhesive bond fails, providing inconclusive engineering data regarding the bonding strength. An alternative test is the block shear joint, which uses a shorter sample geometry and a compressive-shear loading to reduce normal stresses. Analytical models proposed by Goland and Reissner and Hart-Smith are used to compare the edge-bending moment for the two joint configurations. The stress distributions along the bondline are also compared using finite element analysis. Experimental tests are conducted to evaluate these analyses and the failure modes of each configuration are recorded. Block shear samples demonstrate a joint strength over 100% higher than single-lap shear specimen bonded with the same adhesive material. The lower joint strength measured in single-lap shear is found to be potentially misleading due to delamination of the composite adherend.

10 November 2019 in Journal of Composite Materials
Verified
Journal Article
Closed access
PDF file
PBP Breunig
P Breunig
VDV Damodaran
V Damodaran
KSK Shahapurkar
K Shahapurkar
SWSunil Shankar Waddar
Sunil Shankar Waddar
MDM Doddamani
M Doddamani
PPPavana Prabhakar
Pavana Prabhakar
Sandwich composites and syntactic foams independently have been used in many engineering applications. However, there has been minimal effort towards taking advantage of the weight saving ability of syntactic foams in the cores of sandwich composites, especially with respect to the impact response of structures. To that end, the goal of this study is to investigate the mechanical response and damage mechanisms associated with syntactic foam core sandwich composites subjected to dynamic impact loading. In particular, this study investigates the influence of varying cenosphere volume fraction in syntactic foam core sandwich composites subjected to varying dynamic impact loading and further elucidates the extent and diversity of corresponding damage mechanisms. The syntactic foam cores are first fabricated using epoxy resin as the matrix and cenospheres as the reinforcement with four cenosphere volume fractions of 0% (pure epoxy), 20%, 40%, and 60%. The sandwich composite panels are then manufactured using the vacuum assisted resin transfer molding process with carbon fiber/vinyl ester facesheets. Dynamic impact tests are performed on the sandwich composite specimens at two energy levels of 80 J and 160 J, upon which the data are post-processed to gain a quantitative understanding of the impact response and damage mechanisms incurred by the specimens. A qualitative understanding is obtained through micro-computed tomography scanning of the impacted specimens. In addition, a finite element model is developed to investigate the causes for different damage mechanisms observed in specimens with different volume fractions.