An L-shaped tunnel field-effect transistor (LTFET) employs an overlapped gate/channel/source architecture to maximize band-to-band tunneling (BTBT) area. The overlapped channel is very thin and suffers from the geometrical quantum confinement effect (QCE). The analysis of QCE in LTFET has been shown to significantly affect the BTBT in LTFET. As a consequence of QCE, conduction band in the overlapped channel becomes a discrete set of energy subbands, whereas the valence band in the source is continuous. The discretization of conduction band reduces the BTBT drain-source current (Ids) of LTFET. QCE also forces the lateral and parasitic component of BTBT to dominate for a significant portion of the gate-bias swing.
27 June 2013 in IEEE Transactions on Electron Devices
Si/SiO2 interface trap charge distribution of cylindrical cross-sectioned gate-all-around silicon nanowire field-effect transistor is extracted by using three-dimensional simulation. While the interface chemistry of conventional gatestack ( Si/SiO2 polysilicon) in conventional planar devices is well documented, not much work is available on interface trap distribution Dit of alternate gatestacks (gatestacks employing alternate gate materials) in silicon nanowire MOSFET devices. Furthermore, a compact drain current model with interface trap charge parameter is presented. The model is based on gradual channel approximation and uses self-consistent calculation of interface trap charge and surface potential to reproduce experimental current-voltage characteristics.
Trap-assisted-tunneling (TAT) is a well-documented source of severe subthreshold degradation in tunneling field-effect-transistors (TFET). However, the literature lacks in numerical or compact TAT models applied to TFET devices. This work presents a compact formulation of the Schenk TAT model that is used to fit experimental drain-source current (Ids) versus gate-source voltage (Vgs) data of an L-shaped and line tunneling type TFET. The Schenk model incorporates material-dependent fundamental physical constants that play an important role in influencing the TAT generation (GTAT) including the lattice relaxation energy, Huang–Rhys factor, and the electro-optical frequency. This makes fitting any experimental data using the Schenk model physically relevant. The compact formulation of the Schenk TAT model involved solving the potential profile in the TFET and using that potential profile to calculate GTAT using the standard Schenk model. The GTAT was then approximated by the Gaussian distribution function for compact implementation. The model was compared against technology computer-aided design (TCAD) results and was found in reasonable agreement. The model was also used to fit an experimental device’s Ids–Vgs characteristics. The results, while not exactly fitting the experimental data, follow the general experimental Ids–Vgs trend reasonably well; the subthreshold slope was loosely similar to the experimental device. Additionally, the ON-current, especially to make a high drain-source bias model accurate, can be further improved by including effects such as electrostatic degradation and series resistance.
The L-shaped tunneling field-effect-transistor (LTFET) has been recently introduced to overcome the thermal subthreshold limit of conventional metal-oxide-semiconductor field-effect-transistors (MOSFET). In this work, the shortcomings of the LTFET was investigated. It was found that the corner effect present in the LTFET effectively degrades its subthreshold slope. To avoid the corner effect, a new type of device with dual material gates is presented. The new device, termed the dual-gate (DG) LTEFT (DG-LTFET), avoids the corner effect and results in a significantly improved subthreshold slope of less than 10 mV/dec, and an improved ON/OFF current ratio over the LTFET. The DG-LTFET was evaluated for different device parameters and bench-marked against the LTFET. This work presents the optimum configuration of the DG-LTFET in terms of device dimensions and doping levels to determine the best subthreshold, ON current, and ambipolar performance.
The L-shaped tunneling field-effect transistor (LTFET) is the only line-tunneling type of TFET to be experimentally demonstrated. To date, there is no literature available on the compact model of LTFET. In this paper, a compact model of LTFET is presented. LTFET has both one-dimensional (1D) and 2D band-to-band tunneling (BTBT) components. The 2D BTBT part dominates in the subthreshold region, whereas the 1D BTBT dominates at higher gate-source biases. The model consists of 1D and 2D BTBT models. The 2D BTBT model is based on the assumption that the electric field originating from the gate and terminating at the source edge is perfectly circular. Tunneling path length is obtained by calculating the distance along an electric field arc that runs from gate to source. The 1D BTBT model is based on a simultaneous solution of the 1D Poisson equation in source and channel regions. Expressions for electric field and potential obtained from integrating the Poisson equation in source and channel regions are solved simultaneously to find the surface potential. Once the surface potential is known, all the other unknown variables, including junction potential and source depletion length, can be calculated. Using the potential profile, tunneling lengths were found for both the source-to-channel BTBT regime, and channel-to-channel BTBT regime. The tunneling lengths were used to calculate the BTBT tunneling rate, and finally, the drain-source current as a function of gate-source, and drain-source bias was calculated. The model results were compared against technology computer-aided design (TCAD) simulation results and were found to be in reasonable agreement for a compact model.
6 April 2020 in IEEE Transactions on Electron Devices
The default trap-assisted-tunneling (TAT) modeling framework, also known as the dynamic nonlocal TAT model, does not allow to specify multiple trap levels; the lone trap level allowed by the model is not considered in the Poisson-charge self-consistent loop. A method is presented here which allows specifying a trap distribution and the electrostatic degradation (ESD) caused by the trap distribution. The method relies on an individual simulation for each trap level in the distribution, with the total TAT current obtained by summing the TAT currents from the individual trap-level simulations. Ids-Vgs data for an experimental L-shaped tunneling field-effect-transistor (LTFET) were fit using the proposed method, for validation of the proposed method. ESD was found to be an important factor in determining the TAT generation rate (GTAT). The calculated TAT current resulting from a trap distribution allowed to realistically estimate the lifetime parameter, which, if calculated based on a single trap, would be significantly underestimated. From the device point-of-view, this work demonstrates the severity of the TAT problem; TAT was found to dominate for the entire Vgs range, including the ambipolar current, and for all Vds bias values.