MnBi₂Te₄ (MBT) is the first intrinsic magnetic topological insulator with the interaction of spin-momentum locked surface electrons and intrinsic magnetism, and it exhibits novel magnetic and topological phenomena. Recent studies suggested that the interaction of electrons and magnetism can be affected by the Mn-doped Bi₂Te₃ phase at the surface due to inevitable structural defects. Here, we report an observation of nonreciprocal transport, that is, current-direction-dependent resistance, in a bilayer composed of antiferromagnetic MBT and nonmagnetic Pt. The emergence of the nonreciprocal response below the Néel temperature confirms a correlation between nonreciprocity and intrinsic magnetism in the surface state of MBT. The angular dependence of the nonreciprocal transport indicates that nonreciprocal response originates from the asymmetry scattering of electrons at the surface of MBT mediated by magnon. Our work provides an insight into nonreciprocity arising from the correlation between magnetism and Dirac surface electrons in intrinsic magnetic topological insulators.

Electric-field control of magnetism is significant for the next generation of large-capacity and low-power data storage technology. In this regard, the renaissance of a multiferroic compound provides an elegant platform owing to the coexistence and coupling of ferroelectric (FE) and magnetic orders. However, the scarcity of single-phase multiferroics at room temperature spurs zealous research in pursuit of composite systems combining a ferromagnet with FE or piezoelectric materials. So far, electric-field control of magnetism has been achieved in the exchange-mediated, charge-mediated, and strain-mediated ferromagnetic (FM)/FE multiferroic heterostructures. Concerning the giant, nonvolatile, and reversible electric-field control of magnetism at room temperature, we first review the theoretical and representative experiments on the electric-field control of magnetism via strain coupling in the FM/FE multiferroic heterostructures, especially the CoFeB/PMN–PT [where PMN–PT denotes the (PbMn_1/3Nb_2/3O₃)_1−x-(PbTiO₃)_x] heterostructure. Then, the application in the prototype spintronic devices, i.e., spin valves and magnetic tunnel junctions, is introduced. The nonvolatile and reversible electric-field control of tunneling magnetoresistance without assistant magnetic field in the magnetic tunnel junction (MTJ)/FE architecture shows great promise for the future of data storage technology. We close by providing the main challenges of this and the different perspectives for straintronics and spintronics.

To improve the sensitivity of the magnetic tunnel junction(MTJ)sensor, a novel architecture for a double-gap magnetic flux concentrator (MFC) was studied theoretically and experimentally in this paper. The three-dimensional finite element model of magnetic flux was established to optimize the magnetic field amplification factor, with different gaps. The simulation results indicate that the sensitivity of an MTJ sensor with a double-gap MFC can be significantly better than that of a sensor with a traditional single-gap MFC, due to the fact that the magnetic magnification sharply increases with the decrease in effective gap width. Besides this, the half-bridge MTJ sensors with the double-gap MFC were fabricated using photolithography, ion milling, evaporation, and electroplating processes. Experimental results show that the sensitivity of the MTJ sensor increased by ten times compared to the sensor without the double-gap MFC, which underlines the theoretical predictions. Furthermore, there is no significant increase in the sensor noise. The work in this paper contributes to the development of high-performance MTJ sensors.

Magnetic tunnel junction (MTJ) as a key spintronics device can be used for the high-sensitivity magnetic field sensor and high-density non-volatile magnetic random access memory (MRAM). To obtain a high tunneling magnetoresistance (TMR), precise control of the etching process for MTJs is an essential step. In order to investigate the effect of the etching angle on the performance of MTJ devices, a series of MTJ pillars are fabricated by etching with the incidence angle of 10°, 20° and 30°. The prepared samples are characterized by the optical microscopy and SEM, and the R-H curves are also measured and then statistically analyzed. The results reveal that the performance of the MTJ is strongly affected by the IBE process, displaying the uniformity of the pillars edge and MTJ performance will improve as well with the increase of the etching angle. Then, a simplified model based on the re-deposition effect of the etching process is established to explain the experimental phenomena. Furthermore, a newly defined material parameter is introduced in this model and obtained with fitting the experimental results. This proves a valuable way to evaluate the quality of the MTJ stack film without the interference of the device fabrication process.

A highly sensitive superconductor/tunnel magnetoresistance (TMR) composite magnetic sensor was designed and fabricated to satisfy the demands of detecting weak magnetic fields down to the pT range at low frequencies. First, analysis of the 1/f noise provided an optimized design scheme for the TMR unit to reduce the noise level. Then, the key structural parameters of the superconducting flux transformation amplifier (SFTA) were optimized with focus on the bonding quality between SFTA and TMR units using the finite element method to enhance the magnetic field magnification factor. An SFTA–TMR composite method with secondary alignment and multi-step bonding was proposed to fabricate the composite magnetic sensor and ensure the designed bonding gap and alignment accuracy. Experiments showed that the magnetic field sensitivity reached 5 pT/Hz^0.5 (@ 13 Hz), which is beyond the highest level of superconductor/TMR composite magnetic sensors reported to date and is a further step toward the application of weak magnetic field detection.