Maria Cristina Mascolo

Dr. Maria Cristina Mascolo

Department of Civil and Mechanical Engineering, University of Cassino and Southern Latium, G. Di Biasio 43 Street, 03043 Cassino (FR), Italy
orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 February 2019 in Materials
Verified
Journal Article
Open access
PDF file
Grazia AccardoGrazia Accardo
Grazia Accardo
Gianfranco Dell'AgliGianfranco Dell'Agli
Gianfranco Dell'Agli
MMMaria Cristina Mascolo
Maria Cristina Mascolo
Luca SpiridigliozziLuca Spiridigliozzi
Luca Spiridigliozzi
SYSung Pil Yoon
Sung Pil Yoon
To be suitable as electrolytes in intermediate temperature solid oxide fuel cell (IT-SOFC), ceramic precursors have to be characterized by high sintering aptitude for producing fully densified products which are needed for this kind of application. Therefore, synthesis processes able to prepare highly reactive powders with low costs are noteworthy to be highlighted. It has been shown that amorphous coprecipitates based on cerium doped (and codoped) hydrated hydroxycarbonates can lead to synthesized ceramics with such desired characteristics. These materials can be prepared by adopting a simple coprecipitation technique using ammonium carbonate as precipitating agent. As a function of both the molar ratio between carbonate anions and total metallic cations, and the adopted mixing speed, the coprecipitate can be either amorphous, owning a very good morphology, or crystalline, owning worse morphology, packing aptitude, and sinterability. The amorphous powders, upon a mild calcination step, gave rise to the formation of stable solid solutions of fluorite-structured ceria maintaining the same morphology of the starting powders. Such calcined powders are excellent precursors for sintering ceramic electrolytes at low temperatures and with very high electrical conductivity in the intermediate temperature range (i.e., 500–700 °C). Therefore, irrespective of the actual composition of ceria-based systems, by providing an accurate control of both chemical conditions and physical parameters, the coprecipitation in the presence of ammonium carbonate can be considered as one of the most promising synthesis route in terms of cost/effectiveness to prepare excellent ceramic precursors for the next generation of IT-SOFC solid electrolytes.

30 January 2023 in Materials
Verified
Journal Article
Open access
PDF file
Luigi CoppolaLuigi Coppola
Luigi Coppola
Tiziano BellezzeTiziano Bellezze
Tiziano Bellezze
ABAlberto Belli
Alberto Belli
ABAlessandra Bianco
Alessandra Bianco
EBElisa Blasi
Elisa Blasi
AVAntonino Valenza
Antonino Valenza
The increase in concrete structures’ durability is a milestone to improve the sustainability of buildings and infrastructures. In order to ensure a prolonged service life, it is necessary to detect the deterioration of materials by means of monitoring systems aimed at evaluating not only the penetration of aggressive substances into concrete but also the corrosion of carbon-steel reinforcement. Therefore, proper data collection makes it possible to plan suitable restoration works which can be carried out with traditional or innovative techniques and materials. This work focuses on building heritage and it highlights the most recent findings for the conservation and restoration of reinforced concrete structures and masonry buildings.

21 January 2021 in Processes
Verified
Journal Article
Open access
PDF file
Andrea PetrellaAndrea Petrella
Andrea Petrella
Danilo SpasianoDanilo Spasiano
Danilo Spasiano
PCPinalysa Cosma
Pinalysa Cosma
Vito RizziVito Rizzi
Vito Rizzi
Marco RaceMarco Race
Marco Race
EREzio Ranieri
Ezio Ranieri
The photo-catalytic degradation of a textile azo-dye as Methyl Orange was studied in an innovative unit constituted by a channel over which a layer of titanium dioxide (TiO2) catalyst in anatase form was deposited and activated by UVB irradiation. The degradation kinetics were followed after variation of the chemical, physical, and hydraulic/hydrodynamic parameters of the system. For this purpose, the influence of the TiO2 dosage (g/cm3), dye concentration (mg/L), pH of the solution, flow-rate (L/s), hydraulic load (cm), and irradiation power (W) were evaluated on the degradation rates. It was observed that the maximum dosage of TiO2 was 0.79 g/cm3 while for higher dosage a reduction of homogeneity of the cement conglomerate occurred. The Langmuir–Hinshelwood (LH) kinetic model was followed up to a dye concentration around 1 mg/L. It was observed that with the increase of the flow rate, an increase of the degradation kinetics was obtained, while the further increase of the flow-rate associated with the modification of the hydraulic load determined a decrease of the kinetic rates. The results also evidenced an increase of the kinetic rates with the increase of the UVB intensity. A final comparison with other dyes such as Methyl Red and Methylene Blue was carried out in consideration of the pH of the solution, which sensibly affected the removal efficiencies.

6 July 2017
Verified
Conference Paper
Closed access
LWL. Wanik
L. Wanik
MMMaria Cristina Mascolo
Maria Cristina Mascolo
JBJ. BzówKa
J. BzówKa
GMG. Modoni
G. Modoni
Shui-Long ShenShui-Long Shen
Shui-Long Shen
The various technological solutions of jet grouting, normally grouped into single, double and triple fluid, aim principally at increasing the efficiency of treatments obtaining larger diameter of columns and reduce construction time and cost. Rarely attention is put on the influences of the technology on the mechanical properties of the material, considering this as a secondary issue. The present paper focuses on this aspect summarizing the observation of a comprehensive field trial where sixteen columns have been created with single and double fluid jet grouting varying the injection parameters. The large number of laboratory tests performed on samples cored from the columns show a predominant role of the technology, being the material created with single fluid systematically stronger than the one formed with double fluid. This aspect has been herein explored on samples of original soil compared with materials cored from single and double fluid jet columns: the morphology of the samples has been investigated by scanning electron microscopy (SEM), while the mineralogical composition has been inferred with X-ray diffraction (XRD), differential thermal (DTA), and thermo-gravimetric analysis (TGA). The analysis shows that, if on one side the wrapping of the jet with an annulus of compressed air enhances the cutting capacity of the double fluid jet and is this able to create larger diameters, on the other side it leads to a lower proportion of cement in the columns, that is responsible for worse mechanical properties of the material.


1 November 2013 in Microporous and Mesoporous Materials
Verified
Journal Article
Closed access
MMMaria Cristina Mascolo
Maria Cristina Mascolo