Evaluation of transverse impedances and collective instabilities is important for determining whether a transverse feedback system or damping schemes should be prepared in the BRing (Booster Ring) at the HIAF (High Intensity Heavy-ion Accelerator Facility). In this paper, some dominant transverse impedances are estimated to build a transverse impedance model of the BRing. With this model, all potential transverse instabilities and their growth times or rates are analyzed by analytical methods or simulations, and the results agree with each other. The growth times of some instabilities are shorter than the duration times of corresponding manipulations, which shows transverse instabilities may have many detrimental impacts on the BRing. To cure the transverse instabilities, a transverse feedback system will be proposed in the design of the BRing. Besides, this paper not only shows the transverse instabilities in the BRing, but also provides the whole method for estimating them in the design of a new accelerator facility.
11 March 2020 in Physical Review Accelerators and Beams
The transverse broadband impedances of major components in the BRing (booster ring) of HIAF (High Intensity Heavy-ion Accelerator Facility) are estimated using the analytical formulas or the wakefield solver in the CST Studio Suite. At low frequency, the transverse broadband impedance model of BRing is and , which are larger than the threshold impedance for the transverse mode-coupling instability. The ceramic rings in the vacuum chamber are the primary source of impedance. With a goal of mitigating the instability by reducing the impedance of ceramic rings, a high conductivity coating is discussed in detail. In addition, a prototype of ceramic rings-loaded thin-wall vacuum chamber is manufactured and the impedance measurements are performed. When ceramic rings are coated by -copper, the CST simulation and experiment results show that the transverse broadband impedance of ceramic rings-loaded thin-wall vacuum chamber can be reduced from and to and . Furthermore, in this case the transverse broadband impedance model of BRing is reduced by more than 50% to and .
1 July 2001 in Journal of Vacuum Science & Technology A
Aluminum surfaces have been subjected to oxidation at 300 K, using a molecular beam of ozone of 97% purity. An enhancement of the kinetics of oxidation is found compared to oxidation by The oxide film produced exhibits enhanced corrosion resistance as measured by several electrochemical methods compared to comparable thickness oxide films made by oxygen exposure. Transmission electron microscopy measurements show that the ozone-grown films exhibit small pore sizes and also increased average density as measured by the behavior of the radial distribution function derived from electron diffraction measurements on films made from ozone and oxygen. These effects may be due to the lower oxygen vacancy defect density in films made from ozone. The special properties of ozone-grown aluminum oxide films are preserved even after the films are removed from vacuum and exposed to the atmosphere.
1 October 2023 in Review of Scientific Instruments
Dipole magnet vacuum chambers are among the most critical and costly components of rapid-cycling accelerator facilities. Alternative approaches to traditional ceramic chambers have been explored for the implementation of fast-ramping dipole-magnet vacuum chambers, including thin-wall metallic beam pipe chambers strengthened with transverse ribs and ceramic rings inside thin-walled chambers. Here, we report a novel 3D-printed titanium alloy cage inside the thin-wall vacuum chamber, which is designed for high-intensity heavy ion accelerator facility (HIAF) to reduce manufacturing difficulty and cost, shorten the production cycle, and improve the quality. Comprehensive studies were undertaken to characterize the impedance of the 3D-printed titanium alloy cage inside the thin-wall vacuum chamber. The beam-coupling impedance and eddy currents of the new thin-wall vacuum chamber were studied mostly numerically. Strategies for further reducing the beam-coupling impedance were explored. In addition, impedance bench measurements using the “half wavelength” resonant method were conducted to identify the longitudinal and transverse impedances of the 3D-printed titanium alloy cage inside the thin-wall vacuum chamber prototype experimentally. The simulated and measured results for the impedance were consistent. Furthermore, a campaign for resonance-check measurements on the 3D-printed titanium alloy ring loaded inside a thin-wall vacuum chamber prototype was launched. This novel thin-wall vacuum chamber structure is now entering the fabrication stage and will soon be ready for installation in the Booster Ring (BRing).