4 February 1999 in Physics Letters B
New measurements at a centre-of-mass energy GeV of the hadronic photon structure function Fγ2(x) in the Q2 interval, 9 GeV2 ≤Q2≤30 GeV2, are presented. The data, collected in 1997 with the L3 detector, correspond to an integrated luminosity of 51.9 pb−1. Combining with the data taken at a centre-of-mass energy of 91 GeV, the evolution of Fγ2 with Q2 is measured in the Q2 range from 1.2 GeV2 to 30 GeV2. Fγ2 shows a linear growth with lnQ2; the value of the slope α−1dFγ2(Q2)/dlnQ2 is measured in two x bins from 0.01 to 0.2 and is somewhat higher than predicted.
19 March 2020 in Nuclear Science and Techniques
11 March 2020 in Physical Review Accelerators and Beams
The transverse broadband impedances of major components in the BRing (booster ring) of HIAF (High Intensity Heavy-ion Accelerator Facility) are estimated using the analytical formulas or the wakefield solver in the CST Studio Suite. At low frequency, the transverse broadband impedance model of BRing is and , which are larger than the threshold impedance for the transverse mode-coupling instability. The ceramic rings in the vacuum chamber are the primary source of impedance. With a goal of mitigating the instability by reducing the impedance of ceramic rings, a high conductivity coating is discussed in detail. In addition, a prototype of ceramic rings-loaded thin-wall vacuum chamber is manufactured and the impedance measurements are performed. When ceramic rings are coated by -copper, the CST simulation and experiment results show that the transverse broadband impedance of ceramic rings-loaded thin-wall vacuum chamber can be reduced from and to and . Furthermore, in this case the transverse broadband impedance model of BRing is reduced by more than 50% to and .
1 October 2023 in Review of Scientific Instruments
Dipole magnet vacuum chambers are among the most critical and costly components of rapid-cycling accelerator facilities. Alternative approaches to traditional ceramic chambers have been explored for the implementation of fast-ramping dipole-magnet vacuum chambers, including thin-wall metallic beam pipe chambers strengthened with transverse ribs and ceramic rings inside thin-walled chambers. Here, we report a novel 3D-printed titanium alloy cage inside the thin-wall vacuum chamber, which is designed for high-intensity heavy ion accelerator facility (HIAF) to reduce manufacturing difficulty and cost, shorten the production cycle, and improve the quality. Comprehensive studies were undertaken to characterize the impedance of the 3D-printed titanium alloy cage inside the thin-wall vacuum chamber. The beam-coupling impedance and eddy currents of the new thin-wall vacuum chamber were studied mostly numerically. Strategies for further reducing the beam-coupling impedance were explored. In addition, impedance bench measurements using the “half wavelength” resonant method were conducted to identify the longitudinal and transverse impedances of the 3D-printed titanium alloy cage inside the thin-wall vacuum chamber prototype experimentally. The simulated and measured results for the impedance were consistent. Furthermore, a campaign for resonance-check measurements on the 3D-printed titanium alloy ring loaded inside a thin-wall vacuum chamber prototype was launched. This novel thin-wall vacuum chamber structure is now entering the fabrication stage and will soon be ready for installation in the Booster Ring (BRing).
19 November 2020 in IEEE Transactions on Nuclear Science
Stochastic cooling of the Spectrometer Ring (SRing) at the High Intensity heavy-ion Accelerator Facility (HIAF) project in China, which is used mainly for experiments with radioactive fragment beams, is applied to speed up the cooling process of a stored ion beam. In this study, both a Faltin traveling wave structure and a novel slot-ring standing wave structure based on a ceramic vacuum chamber are discussed and evaluated for the pickup/kicker of the SRing stochastic cooling system. The slot-ring structure should significantly improve the shunt impedance due to the Cherenkov effect. For the Faltin-type structure, the results for the pickup shunt impedance obtained from simulations and from beam measurements agree well. Good agreement is also found between the simulated and measured results for the pickup shunt impedance of the slot-ring structure. Cooling process simulations using the Fokker – Planck equation based on the shunt impedance results for the Faltin and slot-ring type pickups are also presented.
22 December 2024 in Nuclear Science and Techniques