Co-combustion of biomass-based fuels and fossil fuels in power plant boilers, utility boilers, and process furnaces is a widely acknowledged means of efficient heat and power production, offering higher power production than comparable systems with sole biomass combustion. This, in combination with CO₂ and other greenhouse gases abatement and low specific cost of system retrofit to co-combustion, counts among the tangible advantages of co-combustion application. Technical and operational issues regarding the accelerated fouling, slagging, and corrosion risk, as well as optimal combustion air distribution impact on produced greenhouse gases emissions and ash properties, belong to intensely researched topics nowadays in parallel with the combustion aggregates design optimization, the advanced feed pretreatment techniques, and the co-combustion life cycle assessment. This review addresses the said topics in a systematic manner, starting with feed availability, its pretreatment, fuel properties and combustor types, followed by operational issues, greenhouse gases, and other harmful emissions trends, as well as ash properties and utilization. The body of relevant literature sources is table-wise classified according to numerous criteria pertaining to individual paper sections, providing a concise and complex insight into the research methods, analyzed systems, and obtained results. Recent advances achieved in individual studies and the discovered synergies between co-combusted fuels types and their shares in blended fuel are summed up and discussed. Actual research challenges and prospects are briefly touched on as well.

The paper presents the results of the optimisation of burner nozzle diameters during the combustion of natural gas under the conditions of increasing oxygen concentrations in the oxidizer in aluminium melting processes in drum rotary furnaces. The optimisation of outlet nozzle diameters was performed employing the method of experimental measurements, the results of which can be used for aluminium melting in hearth furnaces. The measurements were carried out using an experimental upstream burner with 13.5 kW input power. The monitored oxygen concentrations in the oxidizer ranged from 21% to 50%. The measurements were performed and evaluated in two variations of the burner configuration (geometry). In the first study, the impact of the enriched oxidizer on the melting of aluminium ingots was evaluated with the defined diameter of the air nozzle, which resulted in a reduction of the aluminium charge melting time by 50% at 45.16% oxygen concentration in the oxidizer, thus achieving savings in the consumption of fuel used for melting. In the second study, the diameter was optimised depending on the combustion rate of the natural gas and oxidizer mixture. The optimisation of the nozzle parameters resulted in the reduction of the charge melting time by 23.66%, while the same 25% enriched oxidizer was used. With the rise of the enrichment level to 35%, further reduction by approximately 12% was observed. The measurement results prove considerable influence of the parameter (geometry) optimisation of the outlet nozzles and oxidizer enrichment. Appropriately selected parameters of the burner can contribute to achieving comparable results at a lower enrichment of the oxidizer. The obtained results demonstrate the intensification of the heat transfer in the current thermal aggregates. The research conclusions confirm that oxygen-enhanced combustion and modification of existing burners reduces the specific energy consumption on the process and reduces CO₂ emissions.

Air infiltration into the combustion chambers of industrial furnaces is an unwanted phenomenon causing loss of thermal efficiency, fuel consumption increase, and the subsequent increase in operating costs. In this study, a novel design for a rotary tilting furnace door with improved construction features is proposed and tested experimentally in a laboratory-scale furnace, aimed at air infiltration rate reduction by decreasing the gap width between the static furnace door and the rotating body. Temperatures in the combustion chamber and oxygen content in the dry flue gas were measured to document changes in the combustion process with the varying gap width. Volumetric flow values of infiltrating air calculated based on measured data agree well with results of numerical simulations performed in ANSYS and with the reference calculation procedure used in relevant literature. An achievable air infiltration reduction of up to 50% translates into fuel savings of around 1.79 to 12% of total natural gas consumption of the laboratory-scale furnace. The average natural gas consumption increase of around 1.6% due to air infiltration into industrial-scale furnaces can thus likewise be halved, representing fuel savings of almost 0.3 m³ per ton of charge.

Natural gas is currently a hotly debated topic both from an environmental point of view due to the production of CO2 and from an economic point of view. The article is focused on the analysis of selected energy factors when burning natural gas with a gradual increase in the hydrogen content in the fuel mixture. In the article, the authors focused on modelling combustion and the influence of hydrogen concentration on heat flows from flue gas in a thermal aggregate. The aim of the authors is to point out changes combustion in the thermal aggregate using document analysis and calculations. By gradually increasing hydrogen in natural gas, it is possible to prove the effect on heat flows during the exchange of heat from the flue gas to the heated material. According to the results, it can be concluded that increasing the content of methane in natural gas changes the nature of the combustion of the mixture. The combustion temperature increases, heat flow density, on the other hand, the volume of flue gas converted to 1 m3 of fuel decreases. An important factor that positively decreases in this is the CO2 emission factor.

Oxygen-enhanced combustion (OEC) is a useful method for improving the efficiency of thermal plants and for decreasing greenhouse gas (GHG) emissions. Basic and modified burner designs utilizing OEC in the aluminum melting process in a rotary tilting furnace were studied. A combined approach comprising experimental measurement and simulation modeling was adopted aimed at assessing GHG emissions production. Reduction of up to 60% fuel consumption of the total natural gas used in the laboratory-scale furnace was achieved. The optimal oxygen concentration in the oxidizer regarding the amount of total GHG emissions produced per charge expressed as CO₂ equivalent was 35% vol. Its further increase led only to marginal fuel savings, while the nitrogen oxide emissions increased rapidly. Using the modified burner along with OEC led to around 10% lower CO₂ emissions and around 15% lower total GHG emissions, compared to using a standard air/fuel burner. CFD simulations revealed the reasons for these observations: improved mixing patterns and more uniform temperature field. Modified burner application, moreover, enables furnace productivity to be increased by shortening the charge melting time by up to 16%. The presented findings demonstrate the feasibility of the proposed burner modification and highlight its better energy and environmental performance indicators, while indicating the optimal oxygen enrichment level in terms of GHG emissions for the OEC technology applied to aluminum melting.