Existing sewage treatment plants use technologies and treatment methods that do not always provide efficient and reliable wastewater treatment from organic contamination. Among the current methods and principles of wastewater treatment, biological methods, which are considered to be the most promising and environmentally sound, occupy a significant place, therefore, the intensification of biological wastewater treatment is an important task. In order to improve the efficiency of biological wastewater treatment processes, a method of biological activation the microorganisms of active sludge has been proposed, which has significant advantages over other methods. However, the lack of a sufficient scientific and technical base, the use of carboxylic acids to activate the active sludge causes the need for research on the effects of acids on wastewater treatment processes. Experimental studies of the effectiveness of biological stimulation of active sludge’s bacteria with carboxylic acids are presented, theoretically and experimentally justifying the feasibility of consistent use for the treatment of active sludge by lemon and amber acids. The proposed method of intensification of biological wastewater treatment allows us to improve the efficiency of treatment in aeration tanks compared to biological cleansing without the addition of carboxylic acids. In addition, the use of carboxylic acids can have a comprehensive impact on cleaning processes: boost enzyme formation, suppress the development of filamentous bacteria, increase resistance to toxic pollution.
20 December 2025 in Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
Ion exchange plays a key role not only in eliminating water hardness and reducing the concentration of unwanted ions, but also in protecting the environment. Due to its versatility, it is an indispensable tool in modern environmental technologies. Calculation methods are an important component of the implementation of ion exchange technologies, as they play a crucial role in their effective operation. There are calculation methods used in the design of ion exchange systems, but similar methods have not yet been developed to determine operating parameters during operation. This complicates the optimization of the process in real conditions and requires further research and development. The calculation method should be easy to use, but at the same time provide high accuracy of results, taking into account such important factors as water composition, filtration rate, temperature and type of ion exchange resins. It is especially important that the method be developed based on open Python libraries to ensure accessibility and versatility. The differential mathematical approach using Python provides significantly higher accuracy, efficiency and flexibility in calculations. Therefore, the development of an algorithm for solving systems of nonlinear equations by Newton's method will allow achieving maximum accuracy of results. The article develops an algorithm for solving a nonlinear system of equations by Newton's method, which allows determining the distribution of ions in the working zone of the filter in both liquid and solid phases. The implementation of the developed algorithm is carried out using the Python ecosystem. Based on the calculation results, a graph of the output curve is constructed and a complex software module is developed that allows controlling the most important operating parameters of ion-exchange filters. Also, the use of a complex software module will contribute to reducing the operating costs of ion-exchange filters and increasing the efficiency of processes.
18 June 2018 in Eastern-European Journal of Enterprise Technologies
Effectiveness of operation of the membrane bioreactor (MBR) for wastewater treatment with the use of the biological method was considered. The pilot studies were carried out in the test membrane bioreactor, manufactured by company "Alfa Laval" (Denmark). The process of biological treatment of wastewater using the membrane bioreactor makes it possible to intensify the operation of biological treatment plants due to the lack of facilities for settling the sewers, an increase in the dose of active sludge up to 12–13 g/l; the process of deposition is replaced with filtration, washing of membrane modules can be carried out without emptying the tanks and without taking modules out of the tanks. In the process of testing of the membrane bioreactor, based on the module plant, manufactured by company "Alfa Laval" (Denmark) for treatment of domestic wastewater, the treatment mode that meets the requirements for discharge was achieved. Treatment effectiveness by basic indicators was: COD – 93 %, BOD5 – 99 %, suspended substances – 98.5 %, ammonium nitrogen – 98.5%. Operation efficiency of MBR as for nitrates amounted to 89 % after adjustment of reagent’s dose (40–50 mg/l) and the oxygen dose in the nitrification zone (2–3 mg/l). Efficiency of 98.6% for phosphates was achieved after the introduction of the reagent aluminum sulfate with the dosage of 40–50 mg/l. The study conducted has made it possible to obtain the consistent operation mode of the MBR with ensuring effective process of wastewater treatment. Dependences of wastewater treatment efficiency on the MBR as for major contaminants (COD, BOD5, nitrogen compounds and phosphorus) were shown. This enables meeting the strict requirements for wastewater discharge into water bodies and decreasing the cost value of the treatment through a decrease in power consumption. The mechanism of the MBR operation under conditions of treatment of actual wastewater, which allows determining the conditions of the use of the MBR in the technology of the biological wastewater treatment was studied.
Flexible manufacturing systems (FMS) are widely used in modern mechanicalengineering and instrumentation due to their adaptability and high productivity. However,their effective operation is strongly dependent on accurate management of cuttingtool (CT) resources, which are subject to wear during machining processes. This studyaims to develop and justify a methodology for evaluating CT resource consumptionwith higher precision to support decision-making in FMS operations. Machining operationsare classified into positional and contour types based on their tool engagementcharacteristics. For each type, appropriate quantitative wear criteria are proposed: thenumber of discrete tool actions for positional machining and the processed volume orpath length for contour machining. A Monte Carlo-based numerical procedure is developedto estimate the actual volume of material removed during contour operations,accounting for overlapping tool trajectories and idle movements. The results confirmthat the proposed approach significantly improves the accuracy of tool workloadestimation compared to traditional time-based methods. The methodology enables more reliable forecasting of CT wear, supports predictive maintenance strategies, andimproves overall system efficiency. The proposed algorithm can be integrated intodigital manufacturing workflows, contributing to the implementation of intelligenttool management in line with Industry 4.0 objectives.
The article analyzed the problems of environmental monitoring and the level of automation for predicting the state of the environment and the level of use of computer information and analytical systems for environmental expertise.It is established that in order to improve the environmental safety management system and automate the processes of assessing the impact of economic activity on the environment, it is necessary to create software packages aimed at solving various environmental problems, namely receiving wastewater from enterprises to the urban sewerage systems.It is known that the relationship between consumers and water utilities is governed by the Rules of sewage. According to these Rules, the permissible concentrations of pollutants contained in the wastewater of enterprises are determined. But such calculations are characterized by a large number of parameters and a large amount of input data.The authors of the article developed a software package for calculations and rationing of wastewater quality indicators of enterprises that discharge their wastewater into the sewerage network of cities and may disrupt the operation of treatment facilities. In general, the developed software package will reduce the time and perform calculations to determine the permissible concentrations of pollutants in the wastewater of enterprises (consumers), and at the same time analyze large data sets. Automation of the main components of environmental procedures will increase the efficiency and reliability of urban sewerage systems and more effectively assess the impact on the environment. Also, the created software complex will determine the concentration of heavy metals in the sewage sludge and ensure its use as a fertilizer containing more phosphorus and calcium.It should be noted that the created software package allows you to perform such calculations that are difficult to perform in Excel. You can export data from any source - WEB, Excel, OpenOffice. Data and calculation algorithms are separated, which minimizes error. The software package was created using Node.js technology.