Qais Abdulrahman Ali Qais

Dr. Qais Abdulrahman Ali Qais

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 August 2026 in Materials
Verified
Journal Article
Open access
PDF file
AMAli Mardani
Ali Mardani
MHMohammad Hematibahar
Mohammad Hematibahar
SOSELIN OZTEBER
SELIN OZTEBER
QQQais Abdulrahman Ali Qais
Qais Abdulrahman Ali Qais
IKIvan Khalil
Ivan Khalil
AEAhmed Elsheikh
Ahmed Elsheikh
The structural use of three-dimensional concrete printing remains limited by the directional weakness introduced during extrusion and layer-by-layer deposition. Although 3DPC offers major advantages in formwork elimination, architectural freedom, and automated construction, its printed architecture produces interfaces, pore networks, and reinforcement discontinuities that do not exist in the same form in conventionally cast concrete. This review examines the anisotropic behavior of 3DPC by linking its architectural arrangement, physical interlayer mechanisms, and chemical durability-related processes. The analysis shows that anisotropy develops from the combined effects of filament orientation, interlayer bonding quality, pore morphology, cold-joint formation, mechanical interlocking, hydration continuity, and reinforcement limitations. Weak interlayer regions act not only as preferred paths for crack initiation and propagation under tensile, flexural, shear, and compressive loading, but also as transport channels that accelerate water absorption, chloride ingress, carbonation, sulfate attack, and freeze–thaw deterioration. The review further highlights that fiber, textile, FRP, and discrete reinforcement strategies can reduce some consequences of anisotropy, but their effectiveness depends on whether they bridge the weaker interlayer regions rather than merely reinforcing the filament direction. SEM-based observations confirm that microstructural discontinuities, fiber-matrix debonding, irregular hydration products, and connected pores provide the material-level basis for the directional response of printed concrete. Overall, anisotropy should be treated as a design-critical feature of 3DPC rather than as a secondary defect. Reliable structural application requires coordinated control of mixture rheology, deposition parameters, interlayer timing, curing, toolpath design, and reinforcement layout.

24 March 2026 in Construction Materials and Products
Verified
Journal Article
Closed access
QQQais Abdulrahman Ali Qais
Qais Abdulrahman Ali Qais
GOG.E. Okolnikova
G.E. Okolnikova
Hybrid basalt fibre-reinforced concrete (HBFRC) has emerged as a high-performance material capable of addressing the severe mechanical demands placed on aerodrome pavement systems. By integrating basalt micro and macro fibres, the composite gains improved stiffness, enhanced crack-arrest capacity, and greater resistance to repeated aircraft-induced loads. This study develops and analyses 25 hybrid concrete mixes using both laboratory testing and a detailed finite element simulation in Ansys Workbench to quantify how different fibre proportions influence compressive strength, stiffness, and deformation under an Airbus A321neo load. A 3D fracture-based pavement model incorporating predefined semi-elliptical crack geometry was used to evaluate the de-formation response across 7-, 14-, and 28-day curing periods. Results show a clear improvement in mechanical performance with hybridisation, with the mix containing 2% basalt microfibres and 1% macrofibres consistently yielding the lowest deformation values (0.0054353mm, 0.005815mm and 0.0057363mm) for 7 days, 14days and 28 days respectively, indicating superior crack-resistance and load-bearing capacity throughout the curing stages. While the mix containing 0.5% basalt microfibres and 0.5% macrofibres yielded the highest deformation values (0.0059277mm and 0.0058474mm) for 14 and 28 days respectively. The findings demonstrate that optimal hybrid fibre combinations significantly reduce pavement vulnerability to its risk of being susceptible to damage from changing aircraft loads like heaving traffic and can serve as practical reinforcement strategies for strengthening modern airfield infrastructure. The study further highlights the importance of micro–macro fibre synergy in improving fracture behaviour and offers valuable guidance for developing next-generation high-durability airport pavement materials.

1 January 2026 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
PCPaschal Chiadighikaobi
Paschal Chiadighikaobi
ANABBAS ABDULHUSSEIN ABD NOOR
ABBAS ABDULHUSSEIN ABD NOOR
MSMubarak Adedeji Sule
Mubarak Adedeji Sule
QQQais Abdulrahman Ali Qais
Qais Abdulrahman Ali Qais
GOGalina Erikovna Okolnikova
Galina Erikovna Okolnikova
OSOsman Saffia-Doe
Osman Saffia-Doe
The construction industry urgently requires sustainable alternatives to conventional concrete to reduce the high carbon footprint and environmental degradation associated with the extraction of natural aggregates and the use of steel reinforcement. This study investigates the structural performance of granite (G)–bamboo chip (BC) concrete, confined and unconfined in basalt mesh (BM), to identify the mix with the most suitable engineering properties for sustainable concrete production. Experimental and numerical analyses were conducted on six concrete mix series (GBC1–GBC6) prepared with a constant water/binder ratio of 0.40 and a mix ratio of 1:0.59:0.59, where GBC1 (100% G, 0% BCs) served as the control mix. At the same time, GBC2, GBC3, GBC4, GBC5, and GBC6 contained 20%, 40%, 60%, 80%, and 100% BC replacement of G coarse aggregate by volume, respectively. The results showed a decrease in the compressive strength ( f c ) of GBC concrete with increasing BC content except GBC2 replacing 20% G with BC; however, confinement with BM significantly improved the f c . GBC2 exhibited the highest f c of 49.50 N/mm 2 , while GBC3 recorded the highest slump value and the minimum f c of 1.61 N/mm 2 . Water absorption increased with higher BC replacement, ranging from a minimum of 3.1% for GBC1 to a maximum of 16.6% for GBC6. The modulus of elasticity followed a trend similar to the f c , with concrete cubes attaining a maximum of 7.7 × 10 −10 N/mm 2 and a minimum of 1.4 × 10 −10 N/mm 2 , while concrete cylinders recorded a maximum of 8.2 × 10 −11 N/mm 2 and a minimum of 3.6 × 10 −11 N/mm 2 . Stress–strain analysis using ANSYS further showed that GBC2 exhibited the highest maximum and minimum stresses of 47.586 and 34.804 MPa, respectively. Overall, replacing G with BMs in concrete confined with BM resulted in a considerable improvement in strength, demonstrating the potential of this composite system as a high‐performance and environmentally sustainable construction material.

15 December 2024 in Structural Mechanics of Engineering Constructions and Buildings
Verified
Journal Article
Open access
PDF file
AAAhmed Ramadan Ahmed
Ahmed Ramadan Ahmed
QQQais Abdulrahman Ali Qais
Qais Abdulrahman Ali Qais
NYNikolay A. Yermoshin
Nikolay A. Yermoshin
ЕАЕрмошин Николай Алексеевич
Ермошин Николай Алексеевич
Bridge structures are often subjected to extreme conditions such as rough weather, earthquakes, impacts from traffic accidents, and even blasts. Such extreme loads can cause damage to the anchorage zones as a result of high stress concentration and can lead to cable loss. Such extreme loads can cause dam-age to the anchorage zones as a result of a highstress concentration and can lead to cable loss. One of the main targets of this study is to develop an analytical method that increases our understanding of the behavior of long-span cable-supported bridges in the case of the failure of one or several cables,through this method, a formula can be deduced to calculate dynamic amplification factor (DAF) more accurately, which could be useful for academic research. In this study, a parallel-load bearing system is considered as a conceptual model of long-span cable-supported bridges. The objective is to investigate the structural robustness of long-span cablesupported bridges in a cable-loss scenario. The conceptual model consists of a beam suspended from cables (tension elements). A simplified model is intentionally selected to make the analytical approach easier. If examining the simplified model shows a certain phenomenon, a similar phenomenon in more sophisticated models can also be expected. The study considers multiple cable failures and employs an analytical approach, developing an approximation function for stress magnification factor in cable break scenarios, using least squares method. The proposed approximation function is accurate and less than 5% error-free in all tested systems, except for minor β values, and increasing β reduces stress magnifica-tion factor. The parameter β influences the calculation of the cable load. For systems with high β values, smaller design loads are necessary, allowing long-span cable-stayed bridges to be segmented into zones with varying β values. This approach enables the determination of minimum design loads for each zone, ultimately reducing cable design costs in cases of cable loss.

28 January 2026 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PCPaschal Chiadighikaobi
Paschal Chiadighikaobi
MHMohammad Hematibahar
Mohammad Hematibahar
AMAmirali Milani
Amirali Milani
Makhmud KharunMakhmud Kharun
Makhmud Kharun
QQQais Abdulrahman Ali Qais
Qais Abdulrahman Ali Qais
This study focuses on developing predictive models and design equations for 3D‐printed reinforced concrete beams, utilizing machine learning to enhance the accuracy of structural analysis. The research aimed to create a novel equation for predicting bending moments, considering factors like tensile strength, compressive strength, and reinforcement patterns. Key goals included optimizing reinforcement placement and comparing regression models (gradient boosting, lasso, polynomial, stepwise, and random forest). Experiments tested four reinforcement patterns (honeycomb, 3D‐honeycomb, grid, and triangle) in concrete beams, with optimization techniques identifying the best reinforcement position. Machine learning models were evaluated using R 2 , MAE, and RMSE metrics. Results showed gradient boosting as the most accurate ( R 2 = 0.997), with the optimal reinforcement placement at 7.41 mm from the beam’s bottom. SHapley Additive exPlanations (SHAP) analysis highlighted the reinforcement’s tensile strength as the most influential factor, while concrete compressive strength had a minor negative effect. The study provides a validated design equation for 3D‐printed concrete beams, enhancing flexural performance and supporting sustainable construction. By combining machine learning with structural engineering, this work advances innovation in 3D‐printed concrete, offering cost‐effective and efficient solutions for civil engineering applications.

30 August 2026 in Materials
Verified
Journal Article
Open access
PDF file
AMAli Mardani
Ali Mardani
MHMohammad Hematibahar
Mohammad Hematibahar
SOSELIN OZTEBER
SELIN OZTEBER
QQQais Abdulrahman Ali Qais
Qais Abdulrahman Ali Qais
ANABBAS ABDULHUSSEIN ABD NOOR
ABBAS ABDULHUSSEIN ABD NOOR
AEAhmed Elsheikh
Ahmed Elsheikh
The structural application of 3D printed concrete (3DPC) is still constrained by the difficulty of qualifying a layered, process-dependent material using standards developed mainly for cast concrete and conventional masonry. This review examines 3DPC through masonry construction to clarify how interface-controlled behaviour should be interpreted, tested and standardised. The comparison is not based on material similarity, but on the shared structural role of joints, interfaces and assemblage-level load transfer. Most previous reviews mainly discuss printability, mixture design, material development or general mechanical performance. This review instead places the printed interface at the centre of structural qualification, using masonry only as a reference for interpreting joint-controlled load transfer. The review shows that compressive strength alone is insufficient for structural qualification, since printed elements may fail through interlayer debonding, direction-dependent cracking, filament instability, reinforcement discontinuity or connection weakness. Flexural, shear, cyclic and seismic responses are particularly sensitive to interlayer quality, loading orientation and print-path geometry. Existing concrete, mortar and masonry standards remain useful references, but require 3DPC-specific reporting and testing. Accordingly, a tiered qualification route is proposed, progressing from fresh-state characterisation to interface-dominated testing and structural-scale validation.