Even bubble column reactors (BCR) and airlift reactors (ALR) have been developed in terms of various related aspects towards mass transfer enhancement, the effective analysis of gas diffuser types on mass transfer and gas–liquid hydrodynamic characteristics is still limited. Therefore, the present study aims to analyze the relative effect of different types of air diffusers on bubble hydrodynamics and mass transfer performance to understand their behaviors and define the best type. The experiments were conducted by varying different diffuser types, reactor types (BCR and ALR), and superficial gas velocity (Vg) (0.12 to 1.00 cm/s). Five air diffusers including commercial fine sand (F-sand) and coarse sand (C-sand) diffusers, and acrylic perforated diffusers with orifice sizes of 0.3 mm (H-0.3), 0.6 mm (H-0.6), and 1.2 mm (H-1.2), were used in this study. For every condition, it was analyzed in terms of bubble hydrodynamics and oxygen mass transfer coefficient (KLa). Lastly, the selected diffusers that provided the highest KLa coefficient were evaluated with a solid media addition case. The results of both reactor classes showed that F-sand, the smallest orifice diffuser, showed the smallest air bubbles (3.14–4.90 mm) compared to other diffusers, followed by C-sand, which larger about 22–28% on average than F-sand. ALR exhibited a better ability to maintain smaller bubbles than BCR. Moreover, F-sand and C-sand diffusers showed a slower rising velocity through their smaller bubbles and the tiny bubble recirculation in ALR. Using F-sand in ALR, the rising velocity is about 1.60–2.58 dm/s, which is slower than that in BCR about 39–54%. F-sand and C-sand were also found as the significant diffusers in terms of interfacial area and gas hold-up. Then, the KLa coefficient was estimated in every diffuser and reactor under the varying of Vg. Up to 270% higher KLa value was achieved from the use of F-sand and C-sand compared to other types due to their smaller bubbles generated/maintained and longer bubble retention time through slower rising velocity. After adding 10% ring shape plastic media into the reactors with F-sand and C-sand diffusers, a better performance was achieved in terms of KLa coefficient (up to 39%) as well as gas hold-up and liquid mixing. Lastly, ALR also had a larger portion of mixed flow pattern than BCR. This eventually promoted mass transfer by enhancing the mixed flow regime.
Many researchers have focused on multi-phase reactor development for improving mass transfer performance. However, solid particle addition in gas–liquid contactor for better oxygen mass transfer performance is still limited. Hence, this study aims to analyze the relative effect of different types of local solid media on the bubble hydrodynamic characteristics towards mass transfer enhancement in bubble columns (BCR) and airlift reactors (ALR). This was investigated by varying solid media types (ring, sphere, cylinder, and square), solid loadings (0%–15%), and superficial gas velocities (Vg) (2.6–15.3 × 10−3 m/s) in terms of the bubble hydrodynamic and oxygen mass transfer parameters. The result showed that bubble size distribution in BCR and ALR with additional plastic media was smaller than that without media addition, approximately 22%–27% and 5%–29%, respectively, due to the increase of the bubble breaking rate and the decrease of the bubble rising velocity (UB). Further, adding media in both reactors significantly decreased the UB value. Since media increased flow resistance, resulting in decreased liquid velocity, it can also be the moving bed to capture or block the bubbles from free rising. Therefore, oxygen mass transfer performance was investigated. The oxygen transfer coefficient (KLa) in BCR with solid media addition was enhanced up to 31%–56% compared to a non-addition case, while this enhancement was greater at higher solid loading due to its higher effective surface, resulting in a higher bubble break-up rate compared to the lower loading. In ALR, up to 38.5% enhanced KLa coefficient was archived after adding plastic media over the non-addition case. In conclusion, ring and cylinder media were found to be the most significant for improving KLa value in BCR and ALR, respectively, without extra energy.
Oxygen scarcity may significantly affect the process performance since it has low aqueous solubility and high demand by chemical and biological processes. The oxygen mass transfer is therefore necessary to enhance. This work aimed to develop the gas-liquid reactor, named Modified Airlift Reactor (MALR) for improving the oxygen transfer efficiency in terms of internal configurations and aeration parameters by equipping a vertical baffle for creating liquid circulation phenomena, and installing slanted baffles in the reactor riser to extend air-bubbles retention time and to improve their distributions. Since extremum conditions of the investigated factors may inefficient, optimum levels are required to identify. 2k factorial and response surface design of Design of Experiment (DOE) methodology were applied to optimize these complex variables in terms of overall liquid mass transfer coefficient (KLa) of clean water. As a result, the main effective factors of MALR with their optimum value are amount of baffles (Nb ∼ 3 baffles), baffle angle (α ∼ 50°), position of base area (Yr ∼ 10 cm), open space on baffle (As ∼ 90 cm2), and gas flow (Qg). Increasing Qg resulted better KLa for the studied ranges (2–18 LPM). At the optimum condition, the improvement of MALR in terms of KLa coefficient was increased up to 97% and 28% compared to the regular bubble column and airlift reactor, respectively, at a certain gas flow without any extra energy. The correlation models of KLa coefficient with significant variables and power consumption were constructed for future estimation purposes. GRAPHICAL ABSTRACT
To propose an efficient system for addressing water scarcity in a rural area through groundwater use, the information on water consumption and interpretation of groundwater quality are essential for estimating the optimal preparation of the comprehensive water system. Hence, this study aimed to estimate the current household domestic water consumption and groundwater quality index of currently accessed wells in a small rural community of Preyveng province, Cambodia as a practical and beneficial as well as a model for the water resource sector in rural areas. The questionnaire survey was designed as the main instrument for collecting the household water use as face-to-face interviews. The result showed that the average daily water consumption in the Preal commune is about 71 L per capita, which is almost two times lower than the minimum water quantity recommended by the World Health Organization (WHO), 150 L/day per capita. Moreover, 100% of the households in this commune heavily rely on groundwater wells for domestic water use and more than 50% confirmed that they used raw groundwater as drinking water without a proposer treatment system. Approximately 70% of the people in Preal wishes to have a clean water supply and more than 80% of the household had a positive willingness to pay for clean water supply. In terms of groundwater quality in the Preal commune, it is mainly contaminated by iron, arsenic, fluoride, and manganese, which are mainly associated with human health effects from daily consumption. About 75% of groundwater wells are presented in poor conditions and were unsuitable for drinking purposes. Lastly, the suitable water treatment and supply should be considered in order to reduce the effects on people’s health as well as to improve living conditions.
14 October 2019 in Multiscale and Multidisciplinary Modeling, Experiments and Design