This study aims to develop more inclusive and sustainable waste management practices to be implemented in Bang Chalong Housing, a model community with unsatisfactory waste separation and recycling rate. The extended theory of planned behavior was employed to investigate the effect of attitude, subjective norm, perceived behavioral control, knowledge, and situational factors on household waste separation intention and behavior, using structural equation modeling as a tool. Based on the questionnaire responses of 321 residents, the house owner’s status exhibited a considerable impact on waste-sorting behavior. Knowledge (β = 0.653; p < 0.001) and subjective norm (β = 0.160; p < 0.05) were two significant predictors of the respondents’ intention, which showed a strong influence on household waste separation behavior (β = 0.804; p < 0.001). Various waste management scenarios were also evaluated through material flow analysis and life cycle assessment. Installing a waste-sorting plant in addition to the current approach (recycling and landfilling) could annually reduce 26.4 tons of solid waste from being landfilled and mitigate GHG emissions by up to 47.4 tons CO2 equivalent. Finally, the implications of these results on designing interventions and amending waste management schemes were discussed.
9 November 2017 in Chemical Engineering & Technology
Even bubble column reactors (BCR) and airlift reactors (ALR) have been developed in terms of various related aspects towards mass transfer enhancement, the effective analysis of gas diffuser types on mass transfer and gas–liquid hydrodynamic characteristics is still limited. Therefore, the present study aims to analyze the relative effect of different types of air diffusers on bubble hydrodynamics and mass transfer performance to understand their behaviors and define the best type. The experiments were conducted by varying different diffuser types, reactor types (BCR and ALR), and superficial gas velocity (Vg) (0.12 to 1.00 cm/s). Five air diffusers including commercial fine sand (F-sand) and coarse sand (C-sand) diffusers, and acrylic perforated diffusers with orifice sizes of 0.3 mm (H-0.3), 0.6 mm (H-0.6), and 1.2 mm (H-1.2), were used in this study. For every condition, it was analyzed in terms of bubble hydrodynamics and oxygen mass transfer coefficient (KLa). Lastly, the selected diffusers that provided the highest KLa coefficient were evaluated with a solid media addition case. The results of both reactor classes showed that F-sand, the smallest orifice diffuser, showed the smallest air bubbles (3.14–4.90 mm) compared to other diffusers, followed by C-sand, which larger about 22–28% on average than F-sand. ALR exhibited a better ability to maintain smaller bubbles than BCR. Moreover, F-sand and C-sand diffusers showed a slower rising velocity through their smaller bubbles and the tiny bubble recirculation in ALR. Using F-sand in ALR, the rising velocity is about 1.60–2.58 dm/s, which is slower than that in BCR about 39–54%. F-sand and C-sand were also found as the significant diffusers in terms of interfacial area and gas hold-up. Then, the KLa coefficient was estimated in every diffuser and reactor under the varying of Vg. Up to 270% higher KLa value was achieved from the use of F-sand and C-sand compared to other types due to their smaller bubbles generated/maintained and longer bubble retention time through slower rising velocity. After adding 10% ring shape plastic media into the reactors with F-sand and C-sand diffusers, a better performance was achieved in terms of KLa coefficient (up to 39%) as well as gas hold-up and liquid mixing. Lastly, ALR also had a larger portion of mixed flow pattern than BCR. This eventually promoted mass transfer by enhancing the mixed flow regime.
Many researchers have focused on multi-phase reactor development for improving mass transfer performance. However, solid particle addition in gas–liquid contactor for better oxygen mass transfer performance is still limited. Hence, this study aims to analyze the relative effect of different types of local solid media on the bubble hydrodynamic characteristics towards mass transfer enhancement in bubble columns (BCR) and airlift reactors (ALR). This was investigated by varying solid media types (ring, sphere, cylinder, and square), solid loadings (0%–15%), and superficial gas velocities (Vg) (2.6–15.3 × 10−3 m/s) in terms of the bubble hydrodynamic and oxygen mass transfer parameters. The result showed that bubble size distribution in BCR and ALR with additional plastic media was smaller than that without media addition, approximately 22%–27% and 5%–29%, respectively, due to the increase of the bubble breaking rate and the decrease of the bubble rising velocity (UB). Further, adding media in both reactors significantly decreased the UB value. Since media increased flow resistance, resulting in decreased liquid velocity, it can also be the moving bed to capture or block the bubbles from free rising. Therefore, oxygen mass transfer performance was investigated. The oxygen transfer coefficient (KLa) in BCR with solid media addition was enhanced up to 31%–56% compared to a non-addition case, while this enhancement was greater at higher solid loading due to its higher effective surface, resulting in a higher bubble break-up rate compared to the lower loading. In ALR, up to 38.5% enhanced KLa coefficient was archived after adding plastic media over the non-addition case. In conclusion, ring and cylinder media were found to be the most significant for improving KLa value in BCR and ALR, respectively, without extra energy.
Oxygen scarcity may significantly affect the process performance since it has low aqueous solubility and high demand by chemical and biological processes. The oxygen mass transfer is therefore necessary to enhance. This work aimed to develop the gas-liquid reactor, named Modified Airlift Reactor (MALR) for improving the oxygen transfer efficiency in terms of internal configurations and aeration parameters by equipping a vertical baffle for creating liquid circulation phenomena, and installing slanted baffles in the reactor riser to extend air-bubbles retention time and to improve their distributions. Since extremum conditions of the investigated factors may inefficient, optimum levels are required to identify. 2k factorial and response surface design of Design of Experiment (DOE) methodology were applied to optimize these complex variables in terms of overall liquid mass transfer coefficient (KLa) of clean water. As a result, the main effective factors of MALR with their optimum value are amount of baffles (Nb ∼ 3 baffles), baffle angle (α ∼ 50°), position of base area (Yr ∼ 10 cm), open space on baffle (As ∼ 90 cm2), and gas flow (Qg). Increasing Qg resulted better KLa for the studied ranges (2–18 LPM). At the optimum condition, the improvement of MALR in terms of KLa coefficient was increased up to 97% and 28% compared to the regular bubble column and airlift reactor, respectively, at a certain gas flow without any extra energy. The correlation models of KLa coefficient with significant variables and power consumption were constructed for future estimation purposes. GRAPHICAL ABSTRACT
The destabilization mechanism of the high stable cutting-oil emulsion by aluminum sulfate (Al2(SO4)3) was investigated since it can affect properties of aggregates and following separation units. Al2(SO4)3 dosage and pH were key factors in the destabilization. The effective separation occurred when precipitated Al(OH)3 is dominated at the neutral pH of 6.5–7.0. The best separation can be achieved when solid flocs were formed at 1.0 mM, which exceeded the dosage from the critical coagulation concentration (CCC) of 0.75 mM. Two different mechanisms were proved for the emulsion destabilization depending upon the Al3+ concentration under this pH range. The first mechanism was the adsorption of Al(OH)3 on surface of oil droplets, which led to the droplet coalescence. By increasing the Al3+ dosage, the sweep flocculation by Al(OH)3 precipitates occurred. Al3+ dosage for effective destabilization was increased in accordance with oil concentration. The formation of aluminum hydroxide precipitates in bayerite structure was affirmed by analyzing elemental composition and crystalline structure of flocs from the destablization.