We describe the external and internal hydrogen interaction on contacting surfaces in the “cylinder–piston rings” friction coupling. Under the influence of high temperatures and pressure, the oil in the combustion chamber at a temperature up to 1473 K decomposes and forms small amounts of water. External hydrogen (H2) is subsequently formed. Hydrogen removal from the piston rings reduces the heterogeneity of the structure, residual stresses, and uneven physical and chemical properties of the near-surface layers, which reduces the stress concentration and, as a consequence, results in an improvement in the performance characteristics of the surface layers of the friction couple “cylinder-piston rings” of the spark ignition engine.
The article is devoted to the following issues: boiling of fluid in the cooling jacket of the engine cylinder head; agents that influenced the thermal conductivity coefficient of nanofluids; behavior of nanoparticles and devices with nanoparticles in the engine’s cylinder head cooling system. The permissible temperature level of internal combustion engines is ensured by intensification of heat transfer in cooling systems due to the change of coolants with “light” and “heavy” nanoparticles. It was established that the introduction of “light” nanoparticles of aluminum oxide into the water in a mass concentration of 0.75% led to an increase in its thermal conductivity coefficient by 60% compared to the base fluid at a coolant temperature of 90 °C, which corresponds to the operating temperature of the engine cooling systems. At the indicated temperature, the base fluid has a thermal conductivity coefficient of 0.545 W/(m °C), for nanofluid with particles its value was 0.872 . At the same time, a positive change in the parameters of the nanofluid in the engine cooling system was noted: the average movement speed increased from 0.2 to 2.0 m/s; the average temperature is in the range of 60–90 °C; heat flux density 2 × 102–2 × 106 ; heat transfer coefficient 150–1000 . Growth of the thermal conductivity coefficient of the cooling nanofluid was achieved. This increase is determined by the change in the mass concentration of aluminum oxide nanoparticles in the base fluid. This will make it possible to create coolants with such thermophysical characteristics that are required to ensure intensive heat transfer in cooling systems of engines with various capacities.
In this article the structural features of friction pairs of brakes are analyzed. Heat transfer processes with new boundary conditions are described analytically with the addition of flow conditions and the appearance of a boundary thermal layer to convective heat transfer. The joint action of heat conduction and convection fields is presented. The release of heat during friction is due to the destruction of adhesive bonds in the actual contact zones, and the stress–strain state of micro-roughnesses. It should be said that due to the presence of accompanying transfer processes, complex heat transfer is much more complex compared to purely conductive, convective, and radiative heat transfer, which significantly complicates its analytical and experimental study. In this regard, the processes of complex heat transfer are currently studied little. From the point of view of non-equilibrium thermodynamics, the main task of describing the transfer process is to establish a relationship between the magnitude of the specific flux and the surface-volume temperatures that it causes in the metallic friction elements of the brakes. Additionally, as a result, an assessment of conductive and convective heat transfer in friction pairs of brake devices was made.
31 August 2023 in Eastern-European Journal of Enterprise Technologies
This paper reports data on the dynamic coefficient of friction and wear of materials of different types of friction pads and brake discs obtained from experimental research during braking under bench conditions. It was established that on the basis of the chemical composition of the materials of the friction pads with codes, in the temperature range of 100–450 °C with a step of 50 °C, the ratio of the maximum to the minimum wear of the disc varies from 6.0 to 10.0. The value of the disc wear ratio at 800 and 1000 brakings, respectively, in the temperature range of 100–250 °C and 100–450 °C was 7.6 and 14.0. This indicates that for pad materials of type A, B, C, and D under the second thermal regime, the linear wear of the working surfaces of the discs is greater than under the first thermal regime. And for the pad materials of type E and F, the wear of the discs was the same. This indicates that the use of traditional pads is characterized by a higher thermal tension of the disc brake friction pair; the absolute temperature values are in the unfavorable zone of 400–700 °C. That, in turn, could lead to both phase changes and thermal fatigue aging of materials and, as a result, to the deterioration of their tribological and thermophysical characteristics in operation. Thus, the implementation of the method of selecting pad components could improve the performance of disc brake devices of cars
The European integration intentions of Ukraine have made changes to the development of its economy and in particular to the financial sphere. Substantially, these changes affected the banking system development, which is a systemic element of the financial and credit market. The essence of these changes manifests itself in the increase of foreign banks presence, the need to implement the EU banking legislation norms and methods of banking business in the domestic practice. All this determines the urgency of the effective development of economic and legal aspects of Ukraine's banking security in the European integration context. From there, the purpose of the article is to clarify the concept of banking security, its main components and levels of development. The report data of the Deposit Guarantee Fund (DGF) and the Prosecutor General’s Office of Ukraine for the last years have been analyzed. It is concluded that the lack of unified reports on the criteria for criminal offenses in the sphere of banking provides a dubious picture of the definite level of these crimes. It also testifies about the lack of control and superficial attitude of the controlling bodies towards the processes of the banking sphere criminalization. It is determined that the DGF indicators do not correspond to those of the Prosecutor General’s Office of Ukraine reports regarding the crimes committed in the sphere of banking. Lack of unified reports as well as the unified terminology and the classification envisaged at the legislative level of these socially dangerous actions complicates identifying the criminological indicators of the crimes in banking. Lack of practice in considering such categories of the cases and the corresponding resolutions of the Plenum of the Supreme Court of Ukraine also does not contribute to the fair court decisions on these matters.
30 June 2021 in Entrepreneurship and Sustainability Issues