Primary-side regulation (PSR) flyback converter with discontinuous conduction modulation (DCM) mode is widely used in small power applications. To introduce higher output power, continuous conduction modulation (CCM) mode is used in which an analog to digital converter (ADC) of high cost is always required. In this paper, to reduce the cost, a novel digital peak current control method is proposed to realize constant output current control in both DCM mode and CCM mode. However, there exists a time length calculation error that cannot be avoided in the critical condition between DCM mode and CCM mode. The output current will be lower than the nominal output current. Thus, a hysteretic multi-mode control method with two PWM modes and two PFM modes is utilized to eliminate the time length calculation error. In the proposed control, only a low speed digital to analog converter (DAC) and three comparators are used which greatly reduced the cost, and high accuracy of output current can be obtained. The proposed control scheme was then verified through a FPGA controlled 3.76-15V/3.76A PSR flyback converter. In the prototype, the accuracy of the output current is within ±1.5% for universal load range.
18 March 2019 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Due to the simple structure and low cost, Primary-Side-Regulation (PSR) flyback converter is widely used in small power applications. As the output voltage is sampled from auxiliary winding in PSR flyback converter, some sampling error exists, especially when Continuous-Conduction-Mode (CCM) is introduced for higher power. To improve constant voltage accuracy, a novel digital controlled sampling strategy is proposed. This scheme uses a digital ramp sampling method to sample output voltage in both DCM and CCM, and proposes a voltage adjustment strategy to adjust sampling errors in CCM without weakening the stability in load-switch process. Finally, the experimental results validate the presented scheme and show that the output voltage error is less than 0.6% in a 20V, 5A PSR flyback prototype.
22 December 2020 in IEEE Transactions on Circuits and Systems I: Regular Papers
Because of the different working principles between conventional flyback and active-clamped flyback (ACF), the existing primary-side regulation (PSR) technology cannot be applied to ACF. And in order to achieve PSR of ACF, a low-cost digital sampling method based on the auxiliary winding of the transformer is proposed. In the conventional peak current mode (PCM) controlled ACF, the sampling resistor of primary current may introduce additional power loss, and high-frequency oscillations during sampling may reduce system’s stability. Therefore, a digital feedback-feedforward control (FFC) method is proposed to eliminate the sampling resistor. The stability of the proposed control method and its influence on the dynamic response are studied. In addition, since GaN device has higher power loss during reverse conduction than its Si counterpart, design considerations of reverse conduction time of power switches are also discussed in this paper. All control methods and design considerations are verified on a GaN-based 12V-3A ACF, and the proposed control strategy is implemented by FPGA.
25 September 2023 in IEEE Transactions on Power Electronics
In this article, a novel digital dual-loop interleaving control algorithm is proposed for an asymmetric multiphase buck converter to further enhance the transient response under the large load step and ultrafast slew rate. The proposed dual loop consists of a novel nonlinear average current loop and a digital integration constant on -time (DICOT) controlled voltage loop, which are interleaving connected. The normal phases with average current control aim to deliver the majority of power, while the auxiliary phases with DICOT control are designed to regulate the output voltage and for the fast transient response. With the interleaving control approach, the average inductor current of auxiliary phases remains unchanged in a steady state under different load conditions and that of normal phases follows the load current level. Compared to existing researches, the proposed digital dual-loop interleaving control has robust operation in auxiliary phases and flexibility control of normal and auxiliary phases, as well as the simple hardware implementation. The proposed algorithm is constructed in field-programmable gate array and is applied on the eight phases asymmetric buck system, the maximum load step of 250 A with the current slew rate of 1200 A/μs is tested, the undershoot and overshoot are 30 and 41 mV respectively, and the recovery times are around 20 μs.
In order to improve the light‐load efficiency of active clamp forward converter with synchronous rectifier (SR), power loss analysis of the converter operating in continuous conduction mode (CCM) and discontinuous conduction mode (DCM) are presented in this study. The light‐load efficiency of normal ACF converter with SR is low because the output inductor current can go negative when operating in CCM. Considering the fixed frequency control only, to shift the converter's operating mode from CCM to DCM at a critical point of output current at light‐load is a solution for efficiency improvement. Based on the CCM and DCM power dissipation models proposed in this study, the power loss characteristics of the converter are analysed, and the critical shift point of output current can be derived, which has also been verified by an experimental prototype.