In the United States alone, the cost to repair structures damaged by expansive soils has been estimated to be twice the combined damages of natural disasters. Despite the widespread occurrence of these soils, the damage caused by the presence of expansive soils is regularly overlooked because it might take years of distress exposure before extensive damage to infrastructure can be observed. To predict the heave and swelling pressure an expansive soil will experience in the field, it is standard practice to subject a remolded specimen to a wetting process at a particular net normal stress. This practice does not capture the behavior of expansive soils in the field and therefore, it is necessary to assess the long-term environmental effects on their behavior. In this study, an assessment of the effect of multiple wetting/drying cycles on the volume change behavior of two naturally occurring expansive soils was performed. The soils were remolded at different initial compacted conditions, loaded to different net normal stresses, wetted to nearly 100% saturation and then subjected to full drying. In general, it was observed that after four cycles, the swelling or collapse strain and the swell pressure reached equilibrium. When the applied stress exceeded 25% of the swell pressure, both soils exhibited an increase in collapse potential from the previous wetting cycle. However, when the applied stress was less than 25% of the swell pressure, both soils exhibited an increase in swell potential from the previous cycle.
1 February 2011 in Journal of Performance of Constructed Facilities
Construction on expansive soils is challenging and thus prone to some problems and litigation. The engineering community makes extensive use of local experience and empirical procedures to address these problems. Although there has been extensive study of expansive soils and foundations on expansive soils, data related to performance of residential structures are limited in general and limited in the Phoenix area, in particular. In this study, an overview of the Phoenix Valley, Arizona, geotechnical practice and foundation performance related to residential structures on expansive clays, was developed through surveys and interviews with geotechnical engineers, structural engineers, and homebuilders. Using data obtained from files of Phoenix area geotechnical firms and government agencies, the existing Natural Resource Conservation Service map showing expansive soil locations throughout the Phoenix region was updated through the use of correlation developed in this study relating expansion index to common ...
During the last decade several researchers and practitioners have stressed the importance and the need of adopting unsaturated soil mechanics in the analysis of problems associated with swelling clays and other problematic unsaturated soils. To accomplish this goal, the determination of the soil-water characteristic curve (SWCC) becomes essential. However, practitioners perceive the SWCC determination as a time consuming and expensive laboratory process. This fact has lead to a slow implementation of unsaturated soil mechanics into geotechnical engineering practice. In an effort to encourage practitioners to employ unsaturated soil mechanics, a study was performed to determine the SWCC based on soil index properties and one measurement of matric suction. In this study, the matric suction of approximately 82 field soil samples was determined using either suction plate or suction membrane devices. It was determined that the proposed procedure provides acceptably reliable approximation of the SWCC.
Relationships between swell potential and soil index properties are commonly used in soil design. It was found that the Expansion Index as determined by the modified Arizona method, EIAZ, correlates very poorly to both Plasticity Index., PI, and percent passing US sieve number 200, P200, when considered separately. The product of these two parameters, however, wPI, improves the correlation from R2 values of 0.41 and 0.27, respectively, to 0.67.
Geotextile offers numerous benefits in improving pavement performance, including drainage, barrier functionality, filtration, and reinforcement. Wicking geotextile, a novel variant in this category, possesses the intrinsic ability to drain water autonomously from soils. This paper details the development and application of a comprehensive multiphysics model that simulates the performance of wicking geotextile within a pavement system under freezing climates. The model considers the inputs of various environmental dynamics, including the impact of meteorological factors, groundwater levels, ground heat, and drainage on the pavement system. The model was firstly validated using field data from a long-term pavement performance (LTPP) road section in the cold region. It was subsequently applied to assess the impacts of wicking geotextile if it was installed on the road section. The model simulated the coupled temporal and spatial variations in soil moisture content and temperature. The simulation results demonstrated that wicking geotextile would create a suction zone around its installation location to draw water from surrounding soils, therefore reducing the overall unfrozen water content in the pavement. The results also showed that the installation of wicking geotextile would delay the initiation of frost heave and reduce its magnitude in cold region pavement.
The influence of temperature on soil engineering properties is a major concern in the design of engineering systems such as radioactive waste disposal barriers, ground source heat pump systems and pavement structures. In particular, moisture redistribution under pavement systems might lead to changes in unbound material stiffness that will affect pavement performance. Accurate measurement of thermal effects on unsaturated soil hydraulic properties may lead to reduction in design and construction costs. This paper presents preliminary results of an experimental study aimed at determining the effect of temperature on the soil water characteristic curve (SWCC) and the unsaturated hydraulic conductivity function (kunsat). Pressure plate devices with volume change control were used to determine the SWCC and the instantaneous profile method was used to measure kunsat. These properties were obtained for two fine-grained materials subjected to controlled temperatures of 5°C, 25°C and 40°C. The results were used to perform a sensitivity analysis of the effect of temperature changes on the prediction of moisture movement under a covered area. The findings were compared to field measured water content data obtained on the subgrade of FAA William Hughes test facility located in Atlantic City. Results indicated that temperature affected the unsaturated hydraulic properties of the two fine-grained materials used in the study. For the DuPont soil, the water retention at 5°C was higher than that for higher temperatures for suction levels lower than about 10,000 kPa; while the kunsat functions were not statistically different. The County soil holds around 10% more moisture at 5°C than at 40°C for suction levels higher than about 1,000 kPa and the kunsat function at 40°C was slightly higher than the function at 5°C. The finding from sensitivity analysis showed that the most accurate modeling was the modeling with unsaturated material properties at 40°C and the difference in unsaturated hydraulic properties did lead to some variations in modeling results.