HÜSEYIN ATA KARAVANA

Prof. Dr. HÜSEYIN ATA KARAVANA

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2020 in Johnson Matthey Technology Review
Verified
Journal Article
Open access
BYBuket Yılmaz
Buket Yılmaz
HKHÜSEYIN ATA KARAVANA
HÜSEYIN ATA KARAVANA
The purpose of this study was to devise an antibacterial treatment for footwear insock leathers. Orange oil-loaded chitosan microparticles were utilised for this purpose. Emulsion formulations with different ratios were prepared, and from these formulations microparticles were manufactured using a spray drying technique. Microparticles obtained in this way were applied to the insock leathers using a finishing process. Successful encapsulation was confirmed by ultraviolet-visible (UV-vis) spectrophotometry, Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) techniques. The microparticles exhibited highly spheroid shape with a size range of 3-5 mu m. Microparticle encapsulation efficiencies ranged from 79.41% +/- 3.36% to 86.60% +/- 1.13%. After performing microbiological tests and in vitro release studies on the insock leathers, it was determined that the prepared microparticles are able to perform core material delivery. Also, successful microparticle application resulted in these leathers acquiring antibacterial properties. The products and process are biodegradable, nontoxic and biocompatible.

17 January 2023 in Coatings
Verified
Journal Article
Open access
PDF file
Liliana IndrieLiliana Indrie
Liliana Indrie
SMSteven McNeil
Steven McNeil
MMMehmet Mete Mutlu
Mehmet Mete Mutlu
SBSanda Bota
Sanda Bota
Dorina Camelia IliesDorina Camelia Ilies
Dorina Camelia Ilies
HKHÜSEYIN ATA KARAVANA
HÜSEYIN ATA KARAVANA
To increase the sustainability of footwear and align it with the circular bioeconomy, there is a pressing need to develop novel bio-based materials to replace the synthetic polymers currently used. In this study, casein-based films were prepared by solution casting with a tannic acid cross-linker, and a glycerol plasticizer. The properties important to footwear materials were characterised, including tensile strength and elongation, stitch strength, hardness, grain cracking strength, water vapour permeability, and thermal properties. The tannic acid imparted a brown colour to the films with good resistance to light-induced fading. Their tensile strengths were 4–5 N/mm2, elongation at break 45%–73%, and water vapour permeability 0.2–0.6 mg/(cm2h), depending upon the levels of the cross-linker and plasticiser. The strength of the films was close to those of some non-leather footwear materials such as compact rubbers and insock materials, but below that required for leather shoe vamps/uppers. The casein films were successfully used in sneaker- and ballerina-style shoes as components of the insock and decorative design elements on the vamp. This work has demonstrated the concept of using casein films in footwear. The properties of the films could be improved by further research, particularly with respect to cross-linking, plasticizing, and combining with bio-based fibers and fabrics.

1 May 2025 in Journal of Industrial Textiles
Verified
Journal Article
Open access
FYFatih Yalçın
Fatih Yalçın
HKHÜSEYIN ATA KARAVANA
HÜSEYIN ATA KARAVANA
The breathability and thermal comfort of footwear, which are essential in everyday life, have a significant impact on user satisfaction. Despite their importance, there is currently no standardised device or procedure to directly test these aspects. The aim of this study is to develop a system and method for evaluating the breathability and thermal comfort of footwear using a foot model that mimics human perspiration and temperature. The model takes into account the distribution of eccrine glands, sweating rate, sweat release areas and foot temperature. Two test principles were applied: (i)measurement of internal temperature and humidity using sensors to assess comfort and (ii)evaluation of moisture management by monitoring the weight gain of footwear, socks and footbed during an 8-h sitting simulation. The system was tested on three full leather military boots, with data collected by sensors and weight measurements. The results showed that 65% of the sweat released was absorbed by the system, with 36% absorbed by the boot, 12% by the footbed and 52% by the sock. The Foot Comfort Logical Scale (FCLS) indicated no temperature discomfort during the trials, but moisture-related discomfort occured after about 240 min and worsened after 300 min when humidity reached 80%. The study demonstrated the effectiveness of the system in simulating the breathability and thermal comfort of footwear, with the results agreeing well with established standards and the literature. Future research will focus on testing different footwear types, incorporating dynamic motion systems and refining the FCLS to improve the accuracy of comfort assessment.

23 December 2024 in Iranian Polymer Journal
Verified
Journal Article
Closed access
PDF file
ABAssel Baidildayeva
Assel Baidildayeva
GTGizem Ceylan TÜRKOĞLU
Gizem Ceylan TÜRKOĞLU
MÖMustafa Ökeer
Mustafa Ökeer
BEBayri Eraç
Bayri Eraç
HKHÜSEYIN ATA KARAVANA
HÜSEYIN ATA KARAVANA

23 March 2026 in Journal of Ambient Intelligence and Smart Environments
Verified
Journal Article
Closed access
CYCagri Yardimci
Cagri Yardimci
FYFatih Yalçın
Fatih Yalçın
HKHÜSEYIN ATA KARAVANA
HÜSEYIN ATA KARAVANA
Maintaining thermal comfort and regulating humidity in footwear is critical, particularly in environments where fluctuations in temperature and moisture impact user experience. Correct estimation of these parameters is crucial in selecting suitable material, thereby improving the efficiency and comfort of the footwear. This study proposes a comparison of the deep learning models (recurrent neural networks, long short-term memory (LSTM), bidirectional LSTM, DeepAR, and hybrid model (Cay, Vassiliadis et al.)) for the forecasting of temperature and humidity inside various types of footwear based on the multi-sensor data. A foot model that mimicked the actual temperature and perspiration process of the human foot was used, and sensor readings were taken from various points of the footwear. Performance of deep learning models was evaluated using four key metrics: mean absolute error, root mean squared error, explained variance score, and mean absolute percentage error. The findings indicate that the hybrid model outperforms the other models and achieves the highest predictive accuracy across all tested footwear conditions. This research contributes to the development of artificial intelligence-based predictive modeling for footwear climate control, offering a robust approach for determining thermophysiological comfort in wearable technologies and smart-manufacturing applications.

30 June 2018 in Tekstil ve Mühendis
Verified
Journal Article
Closed access
EÖErsin Önem
Ersin Önem
AYAli Yorgancıoğlu
Ali Yorgancıoğlu
OYOnur Yılmaz
Onur Yılmaz
HKHÜSEYIN ATA KARAVANA
HÜSEYIN ATA KARAVANA
GZGökhan Zengin
Gökhan Zengin
BBBehzat Oral Bitlisli
Behzat Oral Bitlisli