A single-chip receiver for pulsed laser direct time-of-flight 3-D imaging applications has been realized in a 0.35-μm HV CMOS technology. The chip includes a 32 x 128 single-photon avalanche diode (SPAD) array [35% fill factor (FF)] and 257 time-to-digital converters (TDCs) with a ~78-ps resolution. Two adjacent rows (2 x 128 SPADs) at a time can be selected for simultaneous measurement, i.e., 16 measurement cycles are needed to cover the whole array. SPADs are capable of operating in a gated mode in order to suppress dark and background light-induced detections. The IC was designed to be used in a solid-state 3-D imaging system with laser illumination concentrated in both time (short sub-ns pulses) and space (targeting only the active rows of the SPAD array). The performance of the receiver IC was characterized in a solid-state 3-D range imager with flood-pulsed illumination from a laser diode (LD)-based transmitter, which produced short [~150-ps full-width at half-maximum (FWHM)] high-energy (~3.8-nJ pulse/~14-W peak power) pulses at a pulsing rate of 250 kHz when operating at a wavelength of 810 nm. Two detector/TDC ICs formed an 8k pixel receiver, targeting a field-of-view of ~42° x 21° by means of simple optics. Frame rates of up to 20 fps were demonstrated with a centimeter-level precision in the case of Lambertian targets within a range of 3.5 m.
6 August 2019 in IEEE Transactions on Instrumentation and Measurement
A time-to-digital converter (TDC) often consists of sophisticated, multilevel, subgate delay structures, when time intervals need to be measured precisely. The resolution improvement is rewarding until integral nonlinearity (INL) and random jitter begins to limit the measurement performance. INL can then be minimized with calibration techniques and result postprocessing. The TDC architecture based on a counter and timing signal interpolation (the Nutt method) makes it possible to measure long time intervals precisely. It also offers an effective means of improving precision by averaging. Traditional averaging, however, demands several successive measurements, which increases the measurement time and power consumption. It is shown here that by using several interpolators that are sampled homogeneously over the clock period, the effects of limited resolution, interpolation nonlinearities, and random noise can be markedly reduced. The designed CMOS TDC utilizing internal systematic sampling technique achieves 3.0-ps root mean square (RMS) single-shot precision without any additional calibration or nonlinearity correction.
A laser radar receiver channel targeted at pulsed time-of-flight laser radar applications using 5ns…20ns laser pulses at the 1550nm wavelength region has been designed. The receiver includes a transimpedance preamplifier, post-amplifiers and analog output buffer and has a bandwidth of 15MHz and input reduced total equivalent current noise of ~3nArms without the contribution of the APD noise. The receiver supports both the single shot and transient recording operation modes. By utilizing the time domain compensation methods, the single shot timing walk is at the level of +/−100ps within a wide dynamic range of 1: 36 000 of the received echo amplitudes. It is demonstrated that the designed receiver allows the pulsed time-of-flight measurement in the single shot mode to non-cooperative targets up to distances of several hundreds of meters with a laser pulse power of 4 W and receiver aperture of 20mm.
Full realization of a solid-state 3-D range imager based on the pulsed time-of-flight method is presented. The system uses block-based segmented illumination in the transmitter realized with a 16-element common anode laser diode bar. The receiver is based on a single chip 2-D SPAD/TDC 0.35 μm CMOS array with 32 × 128 SPAD pixels and 257 TDCs. Segmentation of the illumination improves the SN BG R in the detection and results in simpler receiver realization than in the commonly used flood-illumination approach. The system is capable of producing cm-accurate 3-D range images within a FOV of 40° × 10° up to a range of 15 m in normal office lighting at a frame rate of ∼30 fps using a low average illumination power of only 2.6 mW. In background illumination of ∼20 klux, 3-D range images were captured at a distance of ∼13 m using the gated SPAD approach at a frame rate of ∼1 fps.
A solid-state three-dimensional (3-D) range imager using the pulsed time-of-flight principle and a single photon avalanche diode (SPAD) based receiver is demonstrated. Contrary to conventional flood illumination, the suggested system uses sequentially scanned illumination stripes to increase the irradiance under the measured field of view and to reduce the receiver complexity. At equal average illumination power levels this approach increases the signal-to-noise ratio in the receiver enabling thus longer range and/or better performance in high background illumination conditions, albeit at the cost of lower transversal resolution. The transmitter uses eight sequentially driven laser diodes, each of which produces an optical pulse power, length and wavelength of ∼50 W, 2 ns and 905 nm, respectively at a pulse rate of ∼30 kHz so that the total effective pulsing rate is ∼250 kHz and the average illumination power is ∼30 mW. 3-D imaging is demonstrated outdoors in over 50 klux ambient lighting up to ∼10 m distance with 15 Hz frame rate and mm–cm level longitudinal precision in a field of view of about 40×10 degrees. The transversal resolution of the system is 16×128 pixels. The measurement results show 3-D measurement precision scaling according to the laser pulse width and averaging.
A potentially compact 2-D range profiler for non-cooperative targets with a distance range of >10 m is demonstrated. A laser diode utilizing enhanced gain switching is used as a transmitter to provide short, high energy optical pulses (~1 nJ/140 ps). Cylindrical lenses spread the laser beam in one dimension and collimate the beam in the other dimension to illuminate a line shaped field of view of about 45°. A similarly shaped field of view for the detector is realized with a single-photon avalanche diode (SPAD) detector matrix. Compared to a flash 3-D rangefinder, the 2-D rangefinding scheme relaxes the SPAD and time-to-digital converter (TDC) design requirements, increases the signal irradiance at the detector, can have better tolerance for background illumination, and it can be sufficient or advantageous in some applications. The distance measurement precision to each direction is inherently within a few centimeters (FWHM) since the laser pulse width and SPAD detector jitter both correspond with an optical pulse back-and-forth flight time of about a centimeter. Demonstration measurements show >15 Hz line rate and a lateral resolution of about 5 mrad to non-cooperative targets at distances of more than 10 m.