Radiative cooling is a well-researched area. For many years, surfaces relying on radiative cooling failed to exhibit a sub-ambient surface temperature under the sun because of the limited reflectance in the solar spectrum and the reduced absorptivity in the atmospheric window. The recent impressive developments in photonic nanoscience permitted to produce photonic structures exhibiting surface temperatures much below the ambient temperature. This paper aims to present and analyze the main recent achievements concerning daytime radiative cooling technologies. While the conventional radiative systems are briefly presented, the emphasis is given on the various photonic radiative structures and mainly the planar thin film radiators, metamaterials, 2 and 3D photonic structures, polymeric photonic technologies, and passive radiators under the form of a paint. The composition of each structure, as well as its experimental or simulated thermal performance, is reported in detail. The main limitations and constraints of the photonic radiative systems, the proposed technological solutions, and the prospects are presented and discussed.
13 November 2023 in Annual Review of Environment and Resources
Urban overheating is the most documented phenomenon of climate change impacting humans. This article presents the most recent developments on the magnitude and characteristics of urban overheating and the potential synergies with global climatic change. It analyses the latest qualitative and quantitative data on the impact of higher urban temperatures on buildings’ energy supply and demand, heat-related mortality, morbidity and wellbeing, human productivity, survivability of low-income populations, and environmental quality of cities. It describes the state of the art on the development of innovative mitigation materials, advanced urban greenery, heat dissipation, and evaporative techniques as the main mitigation and adaptation technologies to offset the impact of urban overheating. It also analyses the current knowledge on the impact of each mitigation technology on energy, health, environmental quality, urban economy, and survivability. Finally, this article presents the main future challenges related to urban overheating and proposes a specific research agenda to alleviate and counterbalance its impact on human life.
Broadband passive daytime radiative cooling (PDRC) materials exhibit sub-ambient surface temperatures and contribute highly to mitigating extreme urban heat during the warm period. However, their application may cause undesired overcooling problems in winter. This study aims to assess, on a city scale, different solutions to overcome the winter overcooling penalty derived from using PDRC materials. Furthermore, a mesoscale urban modeling system assesses the potential of the optical modulation of reflectance (ρ) and emissivity (ε) to reduce, minimize, or reverse the overcooling penalty. The alteration of heat flux components, air temperature modification, ground and roof surface temperature, and the urban canopy temperature are assessed. The maximum decrease of the winter ambient temperature using standard PDRC materials is 1.1 °C and 0.8 °C for daytime and nighttime, respectively, while the ρ+ε-modulation can increase the ambient temperature up to 0.4 °C and 1.4 °C, respectively, compared to the use of conventional materials. Compared with the control case, the maximum decrease of net radiation inflow occurred at the peak hour, reducing by 192.7 Wm−2 for the PDRC materials, 5.4 Wm−2 for ρ-modulated PDRC materials, and 173.7 Wm−2 for ε-PDRC materials; nevertheless, the ρ+ε-modulated PDRC materials increased the maximum net radiation inflow by 51.5 Wm−2, leading to heating of the cities during the winter.
Trees are considered to be effective for the mitigation of urban overheating, and the cooling capacity of trees mainly comes from two mechanisms: transpiration and shading. This study explores the transpiration cooling of large trees in urban environments where the sea breeze dominates the climate. In the experiment, sap flow sensors were used to measure the transpiration rate of two large trees located in Sydney over one year. Also, the temperature difference between the inside and outside of the canopy, as well as the vertical temperature distribution below the canopy, were measured during summer. In this experiment, the temperature under the canopies decreased by about 0.5 degrees from a 0.5 m height to a 3.5 m height, and the maximum temperature difference between the inside and outside of the canopy was about 2 degrees. After applying a principal component analysis of multiple variables, we found that when a strong sea breeze is the primary cooling mechanism, the sap flow still makes a considerable contribution to cooling. Further, the sea breeze and the transpiration cooling of trees are complementary. In conclusion, the characteristics of synoptic conditions must be fully considered when planting trees for mitigation purposes. Since the patterns of sea breeze and sap often do not coincide, the transpiration cooling of trees is still effective when the area is dominated by sea breeze.
Radiative cooling is a well-researched cooling technique based on the ability of terrestrial surfaces to dissipate heat to the cold space. Past research on radiative cooling failed to present subambient temperatures under direct sunlight due to the limited solar reflectance and emissivity in the atmospheric window. Nanostructures developed in recent years have successfully achieved subambient feature during the daytime. The use of electromagnetic simulation in the design of such structures is essential to understand their optical properties and thus optimize the structures and materials selected before manufacture. In this paper, the commonly used software to solve Maxwell’s equations is first reported. Then the numerical techniques are reviewed and their advantages, limitations, and popularity in academic research are compared and analyzed. After that, the application of these numerical techniques in daytime radiative cooling and the extent of the agreement between their results and those of a reference are discussed. The accuracy analysis of these numerical techniques—including the source of errors in the original calculation, how accuracy of the result is evaluated, and explanations for the discrepancies in results between original and reference computations—are discussed in the final part, as well as the characteristics of numerical technique preferred in radiative cooling. The purpose of this paper is to provide strategies for selecting appropriate numerical techniques according to specific needs, evaluating, and analyzing the accuracy of the calculations, and explaining the cause of discrepancies between original and reference computations.
1 January 2022 in Solar Energy Materials and Solar Cells