A study was conducted on the extraction of volcanic ash from Mount Sinabung through the coprecipitation method to recover silicon dioxide (SiO2). X-ray fluorescence (XRF) analysis showed that the SiO2 content in volcanic ash was 48.5%, and after extraction, it was 99.1%. The morphology showed by...
1 July 2020 in Journal of the Ceramic Society of Japan
In this study, the effects of atmosphere firing and pre-heating treatment on the characteristics of sodium titanates were investigated. The materials were successfully prepared from titanium tetraisopropoxide-sodium chloride (TTIP-NaCl) precursors assisted by organic templates (ethylene glycol and citric acid) via facile templating and hydrothermal methods. Sodium titanates were initially prepared by mixing a sodium precursor solution with a titanium precursor solution at a stoichiometric mole ratio of 1.6:1 under vigorous stirring. This was followed by pre-heating treatment via a hydrothermal method at 150 °C for 6 h and then calcination at 800 °C for 1 h in two different atmospheres including reduction and oxidation conditions. The same process was carried out in the synthesis of the other samples without the preheating treatment. The thermal behaviors of all the as-synthesized samples were evaluated. Meanwhile, the mineralogy and microstructures of all calcined samples were investigated. Both atmosphere firing and pre-heating treatment influenced the thermal behaviors of the as-synthesized sodium titanates, resulting in various sodium titanate types with different microstructures. To prepare the sodium titanates from TTIP-NaCl precursors, the pre-heating treatment and the reduction firing seemed to be the optimum conditions for the formation of sodium titanate, in order to produce Na2Ti6O13-type sodium titanates with rod-like particles in nanometer sizes.
1 March 2024 in Journal of Physics: Conference Series
Manufacture activated carbon bagasse waste has been prepared using H2SO4 catalyst in successful research. Bagasse is made from yellow bagasse. First, carbon C is obtained by drying carbon using an oven at temperature of 300°C for 2.5 hours. Active carbon of bagasse is obtained from activation of 5% H2SO4 (1M) in a ratio of 1:10. The measurements performed in this study were the water absorption test and activated carbon. When measuring the water content, Evaporated substance content, ash content, and bound activated carbon level were measured according to SNI 06-3730-1995. FTIR results showed a sharp and wide peak around 3387 cm−1, 2922.16 cm−1 which shows the vibration of the O-H group on inactivated bagasse carbon, but after activation there is a peak around 3410.15 cm−1. Comparison of the diffraction patterns of carbon before activation and carbon after activation shows that all solids have broad peaks in the 20° - 45° region which is a characteristic peak of carbon and there are also pointed peaks in the 23° and 43° regions. The XRD results showed broadened peaks and absence of pointed peaks, irregular background intensity and showed an amorphous structure.
A hard magnetic strontium hexaferrite was successfully synthesized from SrCl2 and FeCl3 with varying composition of SrCl2 and FeCl3 in stoichiometric ratio (1:6) and non- stoichiometric ratio (1:5.5 and 1:6.5). The synthesis process was carried out by coprecipitation method. The powder then calcined at 950°C and 1050°C, held for 2 hours. Crystal structure was characterized using X-Ray Diffractometer (XRD), showing that the crystal structure is a single phase with stoichiometric ratio at calcination temperature of 950°C. On the other hand, magnetic properties were performed by using Vibrating Sample Magnetometer (VSM). Based on this experiment, it was found some magnetic properties, such as; a magnetic remanent (Br) was 32.47 emu / gram, magnetic coercivity (JHc) was 4.855 kOe.
24 December 2018 in Journal of Physics: Conference Series
Characterization of composites based on the of Durian (Durio Zibethinus Murr) fiber using polyester resin had been done by the method of random orientation. The fibers of 2 cm length in average were extracted using 5 % of NaOH chemical solution for 1.5 hours. The obtained fibers were measured with compositions of 0 gr, 0.1 gr, 0.2 gr, 0.3 g and 0.4 gr. Then, those fibers were mixed by polyester resin and catalyst then pressed uniformly to reduce void on each sample. The mechanical and physical properties of composites were tested by the Electronics System Universal Tensile Machine Type SC – 2DE. The values of tensile strength, flexural strength and strong impact were obtained as 39.165MPa, 46.439MPa and 13.65kJ/mm2, respectively. On the other hand, the bulk density was measured as 1.022/cm3 and the content of water was 2.0 %. The results showed that the mechanical and physical properties are mostly in the required range of the Standard JIS A 5905:2003 such as tensile strength >0.4 MPa, flexural strength >32.0 MPa,bulk density 1.07 – 1.3 gr/cm3 and percentage of water absorption was 5-13%.
1 March 2024 in Journal of Physics: Conference Series
One of the agricultural wastes that has the potential to become high-value products is durian peel waste. This study aims to analyze the parts of durian peel in terms of dry material content, moisture content and FTIR analysis. The method of this research is starting from the selection of ripe durian and durian peel is divided into four parts and labelled as B (thin neck area of white inner peel), C (thick bottom area of white inner peel), A (green and spiny outer peel), and AC (overall combination of C and A). Each section of durian peel has been studied to determine dry material, moisture, and crude fiber content. The results showed that the A segment had the highest dry material content (15.18 %), the B segment had the highest percentage of moisture content (124.1 %) and the FTIR testing of durian peel samples contained O-H, C-H, C≡C, C=O and C=C functional groups. These data have proven that each segment of durian peel has a significant difference in terms of composition value and that the moisture absorption rate of durian peel affects the functional groups.