The widespread industrial application of SnO2-Sb anodes is impeded by the enduring trade-off between electrocatalytic activity and operational stability, mainly due to interfacial passivation and active-layer delamination. To address these limitations, we report a 3D hierarchical Ti foam/TiO2-NTs/SnO2-Sb electrode fabricated via in situ anodic oxidation followed by sol-gel deposition. Vertically aligned TiO2 nanotubes grown directly on the macroporous Ti foam provide a nano-confining, superhydrophilic interlayer that promotes deep wetting of precursor solutions and uniform anchoring of SnO2-Sb nanoparticles. This nanotubular interface reduces charge-transfer resistance, raises the oxygen evolution potential to 2.20 V (vs. SCE), and suppresses parasitic oxygen evolution, thereby improving current efficiency. In phenol degradation, the composite electrode delivers faster kinetics and higher mineralization efficiency than conventional Ti/SnO2-Sb. Accelerated life tests further reveal a markedly prolonged service life, attributed to the 'riveting' effect of the nanotubes, which mitigates thermal stress and restrains passivation-layer growth. These findings highlight a scalable strategy for constructing durable, high-performance porous anodes suited for industrial electrochemical wastewater treatment.
Naproxen sodium is an emerging pollutant that may pose potential hazards to human health and the ecological environment. However, developing highly effective adsorbents for the extraction of naproxen sodium from aqueous environments is still a challenge. Herein, we have prepared a novel amino-functional ionic liquid polymer adsorbent (NH2-IL-PS) for the extraction of naproxen sodium (NPS) from aqueous environments. It was found that the NH2-IL-PS exhibits a high adsorption capacity of 456.6 mg/g for NPS and maintains high extraction efficiency over a wide pH range of 4 to 9 at room temperature. Notably, even when the concentration of NPS was lower than 5 ppb, the extraction efficiency still exceeded 90.0%, with the enrichment factor reaching up to 600.0. More importantly, the NH2-IL-PS adsorbent material can withstand at least 16 consecutive adsorption cycles while maintaining an extraction efficiency of over 90.0%. Finally, the NH2-IL-PS was successfully applied to extract and determine NPS in seven types of real water samples, with relative recoveries ranging from 90.9 to 96.2%. The study of the adsorption mechanism reveals that electrostatic interactions, ion exchange, π-π stacking, and hydrogen bonding are crucial in the extraction of NPS. This study provides a sustainable strategy for the efficient extraction of NPS.
Coal-fired power plants produce large amounts of fly ash that occupy large land areas when stored and pose potential environmental risks. Hence, considerable attention has been drawn to the valorisation of this bulk solid waste, e.g., through CO2 mineralisation. High-alkali Xinjiang Zhundong coal fly ash has a high-silica, low-calcium composition and exhibits a low direct CO2 mineralisation efficiency due to the extensive polymerisation of silicon and aluminium components into an inert glass phase and the very low contents of active calcium and magnesium. In this study, this fly ash was thermochemically modified with a CaSO4 composite flux and used as a CO2 capture agent. The modification and mineralisation conditions were systematically varied to optimise the corresponding parameters (calcination temperature, calcination time, flux loading and flux ratio for modification; solid–liquid ratio, initial CO2 partial pressure and reaction temperature for mineralisation). Thermochemical modification promoted the transformation of inert fly ash components into active calcium silicate phases, with stable CaCO3 generated after mineralisation. Control experiments confirmed that the enhanced CO2 uptake primarily arises from the thermochemical reconstruction of fly ash silicates via calcium incorporation, rather than simple physical mixing with CaSO4. Under optimal mineralisation conditions (60 °C, 2 MPa and a solid–liquid ratio of 200 g/L), the modified fly ash achieved an apparent CO2 conversion rate of 95.82% and an apparent carbon sequestration capacity of 214.6 g CO2 kg−1 modified sample (429.2 g CO2 kg−1 original fly ash). The developed process overcomes the bottleneck of the insufficient carbon sequestration activity of high-silica, low-calcium fly ash, reduces the use of chemical reagents and provides a potential pathway for the valorisation of Xinjiang Zhundong coal fly ash and stable CO2 sequestration.