Cecily Ryan

Cecily Ryan

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2017 in Bioresource Technology
Verified
Journal Article
Closed access
CRCecily Ryan
Cecily Ryan
SBSarah L. Billington
Sarah L. Billington
CCCraig S. Criddle
Craig S. Criddle

10 March 2022 in Composites Part C: Open Access
Verified
Journal Article
Open access
SKSeth Kane
Seth Kane
ERElisabeth Van Roijen
Elisabeth Van Roijen
CRCecily Ryan
Cecily Ryan
SMSabbie Miller
Sabbie Miller

10 May 2022 in Composites Part C: Open Access
Verified
Journal Article
Open access
SKSeth Kane
Seth Kane
CRCecily Ryan
Cecily Ryan


11 December 2018 in Polymers
Verified
Journal Article
Open access
PDF file
JAJesse Arroyo
Jesse Arroyo
CRCecily Ryan
Cecily Ryan
Biobased fillers, such as bio-derived cellulose, lignin byproducts, and biochar, can be used to modify the thermal, mechanical, and electrical properties of polymer composites. Biochar (BioC), in particular, is of interest for enhancing thermal and electrical conductivities in composites, and can potentially serve as a bio-derived graphitic carbon alternative for certain composite applications. In this work, we investigate a blended biopolymer system: poly(lactic acid) (PLA)/poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV), and addition of carbon black (CB), a commonly used functional filler as a comparison for Kraft lignin-derived BioC. We present calculations and experimental results for phase-separation and nanofiller phase affinity in this system, indicating that the CB localizes in the PHBV phase of the immiscible PHBV:PLA blends. The addition of BioC led to a deleterious reaction with the biopolymers, as indicated by blend morphology, differential scanning calorimetry showing significant melting peak reduction for the PLA phase, and a reduction in melt viscosity. For the CB nanofilled composites, electrical conductivity and dynamic mechanical analysis supported the ability to use phase separation in these blends to tune the percolation of mechanical and electrical properties, with a minimum percolation threshold found for the 80:20 blends of 1.6 wt.% CB. At 2% BioC (approximately the percolation threshold for CB), the 80:20 BioC nanocomposites had a resistance of 3.43 × 10 8 Ω as compared to 2.99 × 10 8 Ω for the CB, indicating that BioC could potentially perform comparably to CB as a conductive nanofiller if the processing challenges can be overcome for higher BioC loadings.

13 April 2021 in Materials
Verified
Journal Article
Open access
PDF file
SKSeth Kane
Seth Kane
ATAbby Thane
Abby Thane
Michael EspinalMichael Espinal
Michael Espinal
KLKendra Lunday
Kendra Lunday
HAHakan Armağan
Hakan Armağan
CRCecily Ryan
Cecily Ryan
The development of methods to reuse large volumes of plastic waste is essential to curb the environmental impact of plastic pollution. Plastic-reinforced cementitious materials (PRCs), such as plastic-reinforced mortar (PRM), may be potential avenues to productively use large quantities of low-value plastic waste. However, poor bonding between the plastic and cement matrix reduces the strength of PRCs, limiting its viable applications. In this study, calcium carbonate biomineralization techniques were applied to coat plastic waste and improved the compressive strength of PRM. Two biomineralization treatments were examined: enzymatically induced calcium carbonate precipitation (EICP) and microbially induced calcium carbonate precipitation (MICP). MICP treatment of polyethylene terephthalate (PET) resulted in PRMs with compressive strengths similar to that of plastic-free mortar and higher than the compressive strengths of PRMs with untreated or EICP-treated PET. Based on the results of this study, MICP was used to treat hard-to-recycle types 3–7 plastic waste. No plastics investigated in this study inhibited the MICP process. PRM samples with 5% MICP-treated polyvinyl chloride (PVC) and mixed type 3–7 plastic had compressive strengths similar to plastic-free mortar. These results indicate that MICP treatment can improve PRM strength and that MICP-treated PRM shows promise as a method to reuse plastic waste.