Sohini Chowdhury

Ms. Sohini Chowdhury


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 February 2021 in Materials
Verified
Journal Article
Open access
PDF file
Sapam Ningthemba SinghSapam Ningthemba Singh
Sapam Ningthemba Singh
SCSohini Chowdhury
Sohini Chowdhury
YNYadaiah Nirsanametla
Yadaiah Nirsanametla
Anil DeepatiAnil Deepati
Anil Deepati
CHANDER PRAKASHCHANDER PRAKASH
CHANDER PRAKASH
Catalin PruncuCatalin Pruncu
Catalin Pruncu
Investigation of the selective laser melting (SLM) process, using finite element method, to understand the influences of laser power and scanning speed on the heat flow and melt-pool dimensions is a challenging task. Most of the existing studies are focused on the study of thin layer thickness and comparative study of same materials under different manufacturing conditions. The present work is focused on comparative analysis of thermal cycles and complex melt-pool behavior of a high layer thickness multi-layer laser additive manufacturing (LAM) of pure Titanium (Ti) and Inconel 718. A transient 3D finite-element model is developed to perform a quantitative comparative study on two materials to examine the temperature distribution and disparities in melt-pool behaviours under similar processing conditions. It is observed that the layers are properly melted and sintered for the considered process parameters. The temperature and melt-pool increases as laser power move in the same layer and when new layers are added. The same is observed when the laser power increases, and opposite is observed for increasing scanning speed while keeping other parameters constant. It is also found that Inconel 718 alloy has a higher maximum temperature than Ti material for the same process parameter and hence higher melt-pool dimensions.

1 April 2024 in AIP Advances
Verified
Journal Article
Open access
PDF file
RSRamandeep Singh Sidhu
Ramandeep Singh Sidhu
HFHarnam Singh Farwaha
Harnam Singh Farwaha
Raman KumarRaman Kumar
Raman Kumar
PBPardeep Singh Bains
Pardeep Singh Bains
CHANDER PRAKASHCHANDER PRAKASH
CHANDER PRAKASH
CCChoon Kit Chan
Choon Kit Chan
Metallic Foil Friction Stir Welding (MFFSW) was newly developed from the Friction Stir Welding (FSW) technique. Magnesium (Mg) alloys were the most trending alloys in the aerospace, automobile, and biomedical industries. This study aims to investigate the variation in mechanical, corrosive, microstructural, and fractographic properties of MFFSW as a process innovation when compared with FSW. The metallic foil of pure manganese (Mn) with a thickness of 500 μm was inserted between two AZ61 Mg alloys. The tensile strength, impact strength, and hardness were noted as mechanical properties of the output. Potentiodynamic corrosion tests were performed to reveal the corrosion properties. An optical microscope was used to examine a distinct transverse section of the weld. Fractography tests with scanning electron microscopic analysis were conducted on destructive tensile specimens. The ultimate tensile strength, impact energy, yield strength, and microhardness increased to 16%, 32%, 12%, and 19.17%, respectively, compared to FSW. MMFSW shows a lower elongation of up to 33% than FSW. MMFSW (9.61 mm/A) shows a lower corrosion rate than FSW (11.02 mm/A), which employs improved corrosion properties. Optical microscopy images of the stir zone in both MFFSW and FSW revealed that adding a Mn alloying element improved grain growth uniformity and eliminated unexpected grain growth patterns. Hence, the experiment’s conclusion shows that MFFSW has the edge over FSW for mechanical and corrosion properties. Thus, the Mn strip improves the properties of MFFSW.