The properties of foams are often affected by environmental variables such as salt contamination. The objective of this study is to investigate the impact of salt on the drainage behavior of aqueous foams. To accomplish this objective, drainage experiments were conducted on aqueous foams. Test variables were foam quality (40–65%), and salt content (0% to 18%), and type. To investigate drainage, the foam was generated in a flow loop and trapped in a vertical test section. Then, the pressure profile in the foam column was measured using ten pressure sensors. Foam drainage is determined as a function of time using measured pressure profiles. The results show that the drainage of NaCl-containing foams decreased with foam quality, whereas the CaCl2-containing foams did not exhibit a clear trend with foam quality. The effect of salt content on foam rheology was minimal.
26 April 2012 in Journal of Energy Resources Technology
Steelmaking is an energy-intensive process that generates considerable amounts of by-products and wastes, which often pose major environmental and economic challenges to the steel-making industry. One of these by-products is steel dust that is produced during the separation of impurities in the smelting and refining of metals in steel-making furnaces. In this study, electric arc furnace (EAF) dust has been evaluated as a potential, low-cost additive to increase the viscosity and weight of drilling muds. Currently, the cost of drilling operations typically accounts for 50 to 80% of the exploration costs and about 30 to 80% of the subsequent field development costs. Utilization of steelmaking waste in drilling fluids formulations is aimed to produce new and optimized water-based drilling formulations, which is expected to reduce the amount of bentonite and other viscosifier additives used in the drilling formulations. The results showed that in a typical water-based drilling fluid of 8.6 ppg (1030.51 kg/m3), the amount of standard drilling grade bentonite could be reduced by 30 wt.% with the addition of the proposed new additive to complete the required mud weight. The mixture proved to be stable with no phase separation.
Well integrity is of high importance during the entire well life span especially when renewable energy resources such as geothermal are designed to cover the increasing world energy demand. Many studies have documented the importance of the casing–cement interfacial bonding to ensure critical well integrity achievements; however, laboratory experiments and field data are not always aligned. Furthermore, Finite Element Analysis shows relatively high discrepancies compared with the results of various scholarly published works. The limitations in the FEA are most probably generated by the casing–cement interaction modeling parameters. Typically, the contact between casing and cement is modeled using the so-called CZM method, which includes the shear debonding process into the FEA. Several setups have been used in the past to determine the interfacial casing–cement bonding shear strength. Some of these setups are briefly summarized herein. The novelty of this paper consists in the combination of a relatively simple experimental setup with the finite element modeling of the experiment itself to demonstrate that it is important to acquire accurate laboratory data for debonding simulations and, thus, to improve the well integrity prediction. The aim of this paper is to better understand the limitations of the finite element method when modeling shear bonding of the cement and, in the same, to verify that the proposed experimental setup can be modelled using numerical approaches. The successful numerical simulation can later be used for upscaled models. The results confirm the experimental push down setup and aid engineers to further understand and validate CZM models and optimize the well design to achieve maximum well integrity potential. Our results are within 1% error from the average field data.
11 February 2019 in International Journal of Petrochemistry and Research
Stereolithography (SLA)-based three-dimensional (3D) printing has become a popular tool for creating experimental models to study the two-phase flow behavior in complex flow structures. The main drawback while implementing such models is the wettability nature of the 3D printed surfaces. As non-geological materials are used while printing the porous designs, the flow mechanics do not follow similar patterns as in the reservoir. This work demonstrates the feasibility of using an SLA-based printing technique to replicate a porous structure. The porosity and pore size values of the 3D print are observed to be very close to that of the porous input image of the rock sample. A simple method to modify the surface characteristics of 3D printed surfaces using an ultrasonic-atomized fine spraying technique is developed. Here a thin layer of CaCO3 is deposited on the 3D printed surface by subjecting it to fine alternate sprays of calcium chloride and sodium carbonate. Thirty cycles of coating is observed to have altered the surface's wettability from neutral to oil-wet, resembling a carbonate reservoir.