In a jet impingement cooling (JIC) system, the layout of the target surface and length of the jet holes can change both the flow field and the heat transfer characteristics. Elliptical-shaped pins (ESPs) with different heights and layouts on the target surface of the extended jet hole configurations were examined numerically in a jet impingement system. Normalized nozzle length (Gj/Dj) and normalized pin height (Hp/Dj) were investigated as geometric parameters. Also, the effect of different pin layouts (R1, R2, R3) on heat transfer dissipation was studied by changing the number of pin rows in particular configurations. Numerical analyses were conducted under turbulent flow conditions (16250 ≤ Re ≤ 32500). Nusselt (Nu) numbers, pressure drop, and the thermo-hydraulic performance of the physical model were quantitatively researched to elucidate the underlying mechanisms of enhanced heat transfer by the ESPs. Results showed that area-averaged Nu number on the target wall increased up to 35.82% for Re = 16250 by R2Gj/Dj = 1.0 and Hp/Dj = 0.167 compared to the conventional JIC system. The performance evaluation criterion (PEC) was used to analyze the thermo-hydraulic performance of the examined physical models. According to the PEC values, the most feasible parameters for all Re numbers were R3Gj/Dj = 1.0 and Hp/Dj = 0.167. Furthermore, increasing the number of pin rows in the channel also increased the uniformity of the local heat transfer distribution according to Nu contours.
15 August 2024 in Journal of the Taiwan Institute of Chemical Engineers
The carob, a perennial plant, is grown in regions where the Mediterranean climate is dominant. Because of its properties, it is preferred in many sectors especially in the food and health sectors. Carob is mostly used as sugar and molasses. Moreover, seeds of carob are also used as thickening material in the food sector and its residue is utilized as animal feeding stuff as well. Molasses are mostly produced from carob, grape, mulberry, apple, and pear for many years in Turkey. Molasses production is different from each other with regard to the structure of each fruit. Molasses are produced by pressing in the event of soft. The molasses of hard dried fruits such as carobs which cannot be pressed are obtained by extraction method using water. The parameters which are important for the quality of product such as extraction temperature and duration are not taken into account in the carob molasses obtained by traditional methods. Increasing the amount of water in extraction decreases production efficiency and quality while increasing energy consumption. In this study, the effects of parameters such as water quantity, extraction temperature, duration and the batch number that affect the quality of molasses were experimentally investigated by being used Taguchi method.
31 August 2022 in Sakarya University Journal of Science
Pico hydro turbines are suitable for low head applications in power plants since their efficiency is more stable than other turbine types. In some situations, computational fluid dynamics (CFD) has also been utilized as well as experimental studies for the performance prediction of water turbines at a pico scale. Also, CFD methods are getting much closer to real conditions in terms of steady-state with moving references and transient domains with rotor movements. For this purpose, electricity production related to the flow in a PHT was investigated numerically. This study presents six degrees of freedom (6-DOF) and moving reference frame (MRF) methods to predict the maximum conditions of a pico scale two-dimensional turbine by comparing the torque and angular velocities on the runner based on the turbine output power of 1 W determined by an experimental study. Besides, the effect of the torque, angular velocity, tip speed ratio, and turbine body profile was investigated comprehensively. In this regard, MRF and 6-DOF methods were performed to validate and compare the numerical model with the experimental results. Also, the results obtained from 6-DOF and MRF methods were compared to experimental study. It is concluded that PHT is generating 0.3 W power under 6.47 rad/s angular velocity with 6-DOF method, however; this value corresponds to 31.4 rad/s angular velocity against 1 W with the MRF method. Also, the maximum velocity of the turbine was 6.1 m/s according to the simulation result. It is accepted that the turbine maximum velocity inlet was 0.53 m/s based on the experimental study. As a conclusion, numerical results for the pico hydro turbine were reasonable taking the experimental study into account. It is also concluded that there is a tip speed ratio of 2.36 with the MRF method and 0.48 with the 6-DOF method between water tangential velocity and runner velocity for the turbine model.