Natural dyestuffs are evaluated as innovative natural sources to color the fabric and give antibacterial properties in the textile industry. In this study, methanol extracts of Helichrysum arenarium subsp. aucheri were used as natural sources in wool fabric dyeing. Aluminum potassium sulfate (KAl(SO4)2.12H2O), copper sulfate (CuSO4.5H2O), and iron sulfate (FeSO4.7H2O) metal salts were used in the pre-mordanting process. The dyeing process was carried out in mordant and non-mordant fabrics at 25% and 50% concentrations. In this experiment, fastness values are ranked between medium and good grades. The point that should be especially emphasized is that the un-mordanted and dyed samples’ fastness values are acceptable. The disc diffusion method was applied to determine the antibacterial effect of extracts against Staphylococcus aureus ATCC 25923 and gram-negative Escherichia coli ATCC 25922. The methanol extract obtained from the ultrasonic water bath has shown the most powerful antibacterial effect against S. aureus ATCC 25923 with a 15.8 zone diameter. The dyed wool fabrics demonstrated excellent antimicrobial activity (reduction rates: w38.4e100) against two different bacteria according to AATCC 100 method.
Bacterial cellulose is a raw material that is used in many industrial areas such as textile due to its properties and an alternative to plant cellulose whose usage is increasing day by day. In this research, dissolved bacterial cellulose was used as a coating material. After the coating process, samples were immersed in three different coagulation baths to provide regeneration of the coated material. TGA, FTIR, SEM-EDX, air permeability, tensile test, thermal comfort (alambeta), and water vapor transmission (permetest) analyses were carried out to compare the mechanical, chemical, and thermal properties between raw fabric and treated fabrics. Because of chemical analysis, it was observed that the structures are similar to each other. In terms of thermal stability, it has been determined that the samples that have been coated are more durable than the raw fabric. The tensile test revealed that there was a decrease between 15.05% and 41,62% in the strength of coated materials. According to the results of air permeability, alambeta, and permetest, a decrease in air permeability values, an increase in relative water vapor permeability, and thermal conductivity values were observed with the increase of the remaining coating material in the fabric.
1 December 2017 in Afyon Kocatepe University Journal of Sciences and Engineering
Face masks have an effect of preventing the spread of infectious diseases such as coronavirus disease 2019 (COVID-19). With these masks, it is primarily aimed to prevent the environment from being contaminated by the user. However, in the COVID-19 outbreak, many countries made it mandatory to use masks in areas with high human circulation such as marketplaces, shopping malls and hospitals, and then in all areas outside the home. Some tests such as filtration efficiency, microbial load, resistance to body fluids, flammability and breathability are performed to determine the protection potential and wearing comfort of face masks. In this study, we investigated the bacterial filtration efficiency (%), microbial load (cfu/g), breathability (Pa/cm2) and air permeability values of five different face masks obtained by combining polypropylene (PP) nonwoven layers in different weights (accordance with EN 14683:2019 + AC:2019, EN ISO 11737-1:2018 and TS 391 EN ISO 9237 Standards). The surface morphologies of the nonwoven fabrics were characterized by scanning electron microscope (SEM). It was observed that the weight change in spunbond masks (1–4) was directly proportional to bacterial filtration efficiency and differential pressure, and inversely proportional to air permeability. In addition, SEM analysis showed that the average fiber diameter of the meltblown layer was at least 5.80 times smaller than the spunbond layers, and as a result, dramatic differences were also observed in the air permeability and differential pressure values of the Spunbond-Meltblown-Spunbond (SMS) mask (5) compared to spunbond masks.
Sustainability aims to provide a livable future for the next generations. Studies on reducing high chemical, energy, and water consumption make significant contributions to sustainability in many sectors. The textile sector consists of many processes such as fiber production, yarn and fabric production, dyeing, and finishing processes. Each of these processes consumes a significant amount of water and energy. Cotton fiber production consumes approximately 1559 kg of fresh water per kg, and polyester fiber production consumes approximately 108 kWh of electricity per kg. Clean water consumption can be up to 200 L/kg in subsequent processes such as bleaching, dyeing, printing, and finishing. Surface modification techniques in textile production can play a role in sustainability, especially in areas such as reduction, reuse, and recycling. In this chapter, we aim to investigate the effects of surface modification techniques on reducing chemical, energy, and water consumption in textile production, improving textile performance properties, and altering the service life of textiles.