Power flow control and fault current limitation are two major problems that require an urgent solution in a direct current (dc) grid. This study proposes a novel interline dc power flow controller having a fault current limitation capability (FCL–PFC). The proposed controller is expected to realise overall control of the internal power flow in a dc grid and to limit the fault current under fault conditions. FCL–PFC exhibits small capacity and low loss and does not require energy from an alternating current (ac) system. The topological structure of FCL–PFC is first introduced. Then, the principles of power flow control and self‐power balance using the dc voltage and ac circulating current, respectively, is discussed. The control strategy under stable conditions is further designed. Based on the proposed FCL–PFC action sequence under fault conditions, this study describes the calculation and analysis of the dc fault current in different periods for maximising the fault current limitation ability of FCL–PFC. Finally, a simulation model is used in PSCAD/EMTDC to verify the power flow control and fault current limitation capabilities of the proposed FCL–PFC. The economy of combining FCL–PFC with direct current circuit breakers is analysed.
19 August 2020 in IEEE Transactions on Power Delivery
Power flow controllers and circuit breakers are important devices in a DC grid, and combining them and expanding their ports can save many components. This paper proposes an integrated multiport DC power flow controller with a DC circuit breaker that can achieve power flow control and fault removal on multiple DC lines during steady and fault states, respectively. First, the device's topology based on modular multilevel converters is proposed, and the principles of power flow control and self-power balance based on bridge arm voltage are introduced. Second, it is improved by adding a fault removal capability. The equivalent circuit and fault currents in different time sequences are analyzed, and the component parameter selection method is designed. Third, in the PSCAD/EMTDC, the power flow control and fault removal capabilities are verified using three conditions: flow control, line fault, and bus fault. Finally, the number of components and steady-state losses are analyzed. Overall, the proposed device has power flow control and fault removal functions as well as a certain limiting effect on the fault current, which greatly reduces the system construction cost.
To accurately evaluate the influence of the uncertainty and correlation of photovoltaic (PV) output and load on the running state of power system, a probabilistic optimal power flow (POPF) calculation method based on adaptive diffusion kernel density estimation is proposed in this paper. First, based on the distribution characteristics of PV output, the adaptive diffusion kernel density estimation model of PV output is constructed, which can transform the kernel function into a linear diffusion process to achieve self-tuning of the bandwidth of the nuclear density estimation. This model can fit the distribution of arbitrary distribution of PV power, improve the local adaptability of PV output model, and reflect the uncertainty and volatility of PV output more accurately. Therefore, it can provide more accurate input for POPF calculation. Second, the Kendall rank correlation coefficient and the least Euclidean distance are used as correlation measure and index of fitting to select the optimal Copula function, and the joint probability distribution model of PV output and load is constructed. After extracting the correlated PV output and load samples, a POPF calculation method considering the correlation of PV output and load is proposed by using genetic algorithm (GA), which takes the lowest fuel cost of power generation as the objective function. Finally, simulation studies are conducted with the measured data of a PV power plant of China and the IEEE 30-bus power system. The results show that considering the correlation between PV output and load can improve the accuracy of POPF calculation and effectively reduce the power generation cost of the power system.
In this work, a novel light source of strained InGaAsP/InGaAsP MQW EAM monolithically integrated with DFB laser is fabricated by ultra-low-pressure (22×102Pa) selective area growth (SAG) MOCVD technique. Superior device performances have been obtained, such as low threshold current of 19 mA, output light power of about 7 mW, and over 16 dB extinction ratio at 5 V applied voltage when coupled into a single mode fiber. Over 10 GHz 3 dB bandwidth in EAM part is developed with a driving voltage of 3 V. After the chip is packaged into a 7-pin butterfly compact module, 10-Gb/s NRZ transmission experiments are successfully performed in standard fiber. A clearly-open eye diagram is achieved in the module output with over 8.3 dB dynamic extinction ratio. Power penalty less than 1.5 dB has been obtained after transmission through 53.3 km of standard fiber, which demonstrates that high-speed, low chirp EAM/DFB integrated light source can be obtained by ultra-low-pressure (22×10\+2Pa) SAG method.