In China, preserving historic trees and ancient timber structures has attracted more attention from researchers and institutions. Nondestructive testing (NDT) technology has gained momentum in the application and research in recent years. This paper presents some examples of the application of NDT techniques in the protection of historic trees and ancient timber structures in China. A total of nine NDT techniques were applied, including five techniques of visual inspection, sounding, Resistograph, stress wave transmission velocity, stress wave tomography for both historic trees and ancient timber structures, two techniques of the pulling-test and ground-penetrating radar (GPR) for historic trees alone, and two techniques of acoustic emission (AE) and digital imaging for ancient timber structures. Based on field testing, there is a very good detecting effect for visual inspection and Resistograph, but sounding works unsatisfactorily. The stress wave transmission velocity is found to be excellent in screening for the internal defects of historic tree trunks, but performs badly in screening for the internal defects within the wood members of ancient timber structures. AE is less successful but digital imaging performs well in long-term monitoring and damage warning of wood structures. The stress wave tomography successfully obtains images of internal defects inside tree trunks. The anchorage of some historic trees cannot be quantitatively evaluated with the pulling test if the tree is too large. GPR’s resolution and accuracy are very low, which limit its application. Theoretical research on NDT and promotion of NDT technology are still an essential part of the work in the future.

Tree peony is a deciduous shrub endemic to China, and peony seed oil (PSO) is an important plant oil resource. However, at present, pruning and fruits harvesting of oil tree peony are mainly completed by manual work, which has seriously affected production efficiency. By the need to develop efficient pruning and harvesting equipment for oil tree peony, this study investigated the effect of cutting tool geometric parameters and cutting speed on cutting force and energy. A cutting device was set up, and six cutting tools with different blade angle and sliding-cutting angle were prepared for this research. Stems in different growth stages (anthesis and fructescence) were collected for cutting experiments. In this paper, four blade angles (25°, 30°, 35°, and 40°), three sliding-cutting angles (0°, 10°, and 20°), and four cutting speeds (25 mm/min, 50 mm/min, 100 mm/min, and 200 mm/min) were considered in the experiments. The results showed that cutting force and energy are positively related to blade angle, and the minimum cutting force and energy are required in cutting with 25° blade angle. Compared to straight cutting (sliding-cutting angle is 0°), sliding cutting can obviously reduce the cutting force and energy. Furthermore, the best sliding-cutting angles of cutting tools have discrepancies dependent on the stems in different growth stages. In fructescence, 10° sliding cutting required the lowest cutting force and energy. In contrast, the best sliding-cutting angle of stems in anthesis was 20°. On the other hand, the cutting force and energy were obviously proportional to the cutting speed, which increased by the cutting speed increasing. Therefore, under the condition of ensuring the cutting efficiency, reducing the cutting speed can effectively reduce the power consumption. These results are an important basis for pruning and harvesting machine development for oil tree peony.

Identifying the different damage modes of wood is of great significance for monitoring the occurrence, development, and evolution of wood material damage. This paper presents the research results of the application of acoustic emission (AE) technology to analyze and evaluate the mapping relationship between the damage pattern of wood in the fracture process and the AE signal. For the three-point bending specimen with pre-crack, the double cantilever beam specimen, the single fiber tensile specimen, and the uniaxial compression specimen, the bending tensile compression test and the AE monitoring were performed, respectively. After the post-processing and analysis of the recorded AE signal, the results show that the peak frequency of AE is an effective parameter for identifying different damage modes of wood. In this study, the empirical mode decomposition (EMD) of the AE signal can separate and extract a variety of damage modes contained in the AE signal. The Hilbert–Huang transform (HHT) of the AE signal can clearly describe the frequency distribution of intrinsic mode function (IMF) components in different damage stages on the time scale, and can calculate instantaneous energy accurately, which provides a basis for damage mode recognition and lays a foundation for further accurate evaluation of the wood damage process.

The monitoring of acoustic emission (AE) has allowed tracing of the damage in wooden cultural objects exposed to variations in ambient relative humidity (RH). A year-long on-site AE monitoring of the Song Dynasty shipwreck confirmed the usefulness of the technique in tracing climate-induced damage in wood. New coupling material is tested to make it conform to the conservation rules which is non-corrosive to monitoring objects and a reversible operation. As sensitive parameter of wood damage caused by variations RH, the accumulated ringing counting tends to increase with the increase of daily fluctuation of RH (DFRH). In addition, the damage of wooden cultural objects during shrinkage is stronger than that during swelling. The relationship between the probability of AE activity and the daily DFRH is established and it is determined that the daily variation of RH for long-term protection of the Song Dynasty shipwreck should be controlled within 4%, and an early warning will be given if it exceeds 10%.