In China, preserving historic trees and ancient timber structures has attracted more attention from researchers and institutions. Nondestructive testing (NDT) technology has gained momentum in the application and research in recent years. This paper presents some examples of the application of NDT techniques in the protection of historic trees and ancient timber structures in China. A total of nine NDT techniques were applied, including five techniques of visual inspection, sounding, Resistograph, stress wave transmission velocity, stress wave tomography for both historic trees and ancient timber structures, two techniques of the pulling-test and ground-penetrating radar (GPR) for historic trees alone, and two techniques of acoustic emission (AE) and digital imaging for ancient timber structures. Based on field testing, there is a very good detecting effect for visual inspection and Resistograph, but sounding works unsatisfactorily. The stress wave transmission velocity is found to be excellent in screening for the internal defects of historic tree trunks, but performs badly in screening for the internal defects within the wood members of ancient timber structures. AE is less successful but digital imaging performs well in long-term monitoring and damage warning of wood structures. The stress wave tomography successfully obtains images of internal defects inside tree trunks. The anchorage of some historic trees cannot be quantitatively evaluated with the pulling test if the tree is too large. GPR’s resolution and accuracy are very low, which limit its application. Theoretical research on NDT and promotion of NDT technology are still an essential part of the work in the future.

In this paper, uniaxial compressive strength (UCS) test and three-point bending (TPB) test, together with an acoustic emission (AE) system, were performed to investigate the mechanical properties and AE characteristic changes of concrete with different graphite powder (GP) content. The results show that: (1) Poor adhesion and low interlocking of graphite with cement stone increase the initial defects of concrete, reducing its elastic modulus and the cyclo-hoop effect, and thus weakening the compressive strength. (2) For concrete with a low graphite content, the second sharp rise in ringing counts or energy released during the compressive process can be regarded as a failure alarm. However, as GP content increases, the second sharp rise fades away, while the first sharp rise becomes more visible. At high GP content, the first sharp rise is better for predicting failure. (3) The initial defects caused by GP significantly lower the initial fracture toughness, but its bridging effect greatly increases the critical crack mouth opening displacement and thus significantly enhances the unstable fracture toughness of concrete, by up to 9.9% at 9% GP content. (4) In contrast to compressive process, the sharp increase in AE signals preceding failure during the fracture process cannot be used to predict failure because it occurs too close to the ultimate load. However, as GP can significantly increase the AE signals and damage value in the stable period, such failure precursor information can provide a safety warning for damage development.

The associated effect of sodium chloride and dihydrate gypsum on the mechanical performance of a slag-based geopolymer activated by quicklime was investigated by compressive strength, shrinkage, and square circle anti-cracking tests of mortar with a 0.5 water–binder ratio and a 1:3 binder–sand ratio, as well as paste soundness, powder X-ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscopy with energy dispersive spectroscopy (SEM-EDS), and mercury intrusion porosimetry (MIP) of the paste. The results indicate that (1) when dihydrate gypsum is used alone, it combines with calcium aluminate hydrate (C-A-H) to form calcium sulfoaluminate hydrate (AFt), which encourages the hydration process of slag. A 7.5% addition can result in an increase of 97.33% and 36.92% in 3-day and 28-day compressive strengths, respectively. When NaCl is used by itself, it facilitates the condensation of the aluminum silicate tetrahedron unit and generates zeolite. A 2% dosage can lead to a 66.67% increase in the 3-day compressive strength, while causing a 15.89% reduction in the 28-day compressive strength. (2) The combined effect of 2% NaCl and 7.5% gypsum results in the formation of needle-like and rod-shaped AFt, Friedel’s salt, and plate-like Kuzel’s salt in the geopolymer. This leads to an increase in 3-day and 28-day compressive strengths by 148% and 37.85%, respectively. Furthermore, it reduces the porosity by 18.7%. (3) Both NaCl and gypsum enhance the paste soundness of the slag-based geopolymer, and they do no harm to the crack resistance of the geopolymer. The drying shrinkage of the geopolymer at 28 days is just 0.48 × 10⁻³, which is only 66.7% of OPC. This slag-based geopolymer has a simple preparation process, good volume stability, low raw material cost, low energy consumption, and low carbon emissions. It can be used instead of 32.5 slag Portland cement in plain concrete applications, and has high engineering, economic, and environmental values.

Dolomite rock powder (the waste stone residue in the production of machine-made sand and stone processing) and iron tailings powder formed by mineral processing industry are solid wastes, which occupy land resources, pollute the environment and release toxic substances without reasonable processing. The dolomite rock powder and iron tailings powder composing a large number of active substances could be advantageous to the cement-based materials. In this study, the electrical resistivity of cement paste and concrete was measured. Meanwhile, the influence of dolomite rock powder and iron tailings powder on the compressive strength of concrete was investigated. The electric flux of concrete was determined to estimate the chloride ion permeability. The scanning electron microscope (SEM) and X-ray diffraction were obtained to investigate the hydration of cement paste. Results showed the electrical resistivity of all specimens presented in this order: specimens with iron tailings < specimens with dolomite rock powder < blank specimens < specimens with ground granulated blast-furnace slag (GGBS) < specimens with fly ash. The correlation between electrical resistivity and curing age of cement paste or concrete has been deduced as a quadratic function. The addition of GGBS could improve the compressive strength of concrete. Meanwhile, when the other three types of mineral admixtures were added, 5% by mass ratio of the total binder materials was the optimum for the compressive strength. The curing ages, the fly ash, the GGBS and 5% dolomite rock powder or 5% iron tailings powder demonstrated a positive effect on the chloride ion impermeability. However, when higher dosages of dolomite rock powder or iron tailings powder were added, the effect was the opposite. Finally, the compactness of the microstructure and the Ca(OH)₂ of cement paste could be improved by a small dosage of dolomites or iron tailings (less than 5%).

Traditional Chinese wood residences consist of timber frames with masonry infill walls or other types of infill, representing valuable heritage. A field investigation of traditional village dwellings in northern China consisting of timber frames with mud and stone infill walls was conducted. Their construction characteristics are reported, and static cyclic tests were performed on two full-size wood-stone hybrid walls with different configurations (exterior transverse wall and internal transverse wall) and no openings (doors or windows). Their failure mechanics and seismic capacity, i.e., the strength, stiffness, ductility, and energy dissipation, were investigated. The results are compared with a previous experimental study of two full-size timber frames with the same traditional structure but no infill to determine the effect of the mud and stone infill on the lateral resistance. The experimental results indicate that the stone infill has a critical influence on the lateral performance of traditional village buildings, resulting in a high lateral stiffness, high strength (>20 kN), and a high ductility ratio (>10). An increase in the vertical load leads to an increase in the lateral resistance of the timber frame with infill walls, larger for the internal transverse wall than the external gable wall. The incompatibility of the deformation between the timber frame and stone infill is the main failure reason, resulting in falling stones and collapse with undamaged timber frames. Suggestions are provided for the protection and repair of traditional wood residences in northern China.

Wood is an anisotropic material, the mechanical properties of which are strongly influenced by its microstructure. In wood, grain compression strength and modulus are the weakest perpendicular to the grain compared to other grain directions. FE (finite element) models have been developed to investigate the mechanical properties of wood under transverse compression. However, almost all existing models were deterministic. Thus, the variations of geometry of the cellular structure were not considered, and the statistical characteristic of the mechanical property was not involved. This study aimed to develop an approach to investigate the compression property of wood in a statistical sense by considering the irregular geometry of wood cells. First, the mechanical properties of wood under radial perpendicular to grain compression was experimentally investigated, then the statistical characteristic of cell geometry was extracted from test data. Finally, the mechanical property of wood was investigated using the finite element method in combination with the Monte Carlo Simulation (MCS) techniques using randomly generated FE models. By parameter sensitivity analysis, it was found that the occurrence of the yield points was caused by the bending or buckling of the earlywood axial tracheid cell wall in the tangential direction. The MCS-based stochastic FE analysis was revealed as an interesting approach for assessing the micro-mechanical performance of wood and in assisting in understanding the mechanical behavior of wood based on its hierarchical structure.