Martin László Kölüs

Mr. Martin László Kölüs

orcid

Research Focus & Metrics

Representative Publications

View All Publications
15 May 2024 in Materials Research Proceedings
Verified
Conference Paper
Open access
PDF file
MKMartin László Kölüs
Martin László Kölüs
RBRichárd Borbély
Richárd Borbély
GBGábor J. Béres
Gábor J. Béres
-The effect of friction compensation on the slope of flow curves obtained by stack compression tests KÖLÜS Martin L., BORBÉLY Richárd, BÉRES Gábor J. [butto

30 December 2023 in International Journal of Engineering and Management Sciences
Verified
Journal Article
Open access
PDF file
MKMartin László Kölüs
Martin László Kölüs
RBRichárd Borbély
Richárd Borbély
DSDániel Gyula Szőke
Dániel Gyula Szőke
GBGábor J. Béres
Gábor J. Béres
This study presents the results of finite element simulations based on different variations of the flow curve of DC04 automotive thin sheet. The aim of our research is to investigate how different flow curve equations affect the variation of sheet thickness in cup drawing tests. In order to exclude other influencing factors in the experiment, both the sheet material and the geometric properties of the specimen, as well as the external state factors were considered to be the same in all cases. The finite element simulations were performed using Simufact 2021.1 software. Our results shows that there are no significant differences in wall thicknesses until we reach the zone of double necking, where essential differences are observed.

1 January 2025 in Materials Research Proceedings
Verified
Conference Paper
Open access
PDF file
MKMartin László Kölüs
Martin László Kölüs
GKGábor Kalácska
Gábor Kalácska
GBGábor J. Béres
Gábor J. Béres
This study presents experimental stack compression test results of samples with different height-to-diameter (aspect) ratios for a simplified calculation of the friction- and the stress state contribution on the flow stress compared to the case of simple tension. Standard uniaxial tension tests formed the basis of the investigations as reference curves, and the stack compression tests were carried out on the same material, on commercially available DC04 steel sheet. The aim was to experimentally observe and possibly separate the anisotropic, pure material behavior from the friction-forced reaction of the material to determine the equi-biaxial yield stress for proper yield surface election. Our results show that with proper lubrication conditions, the stress increase caused by friction can be kept at low value for high aspect ratios, as well as with the comparison of the high and low aspect ratios, the value of the Coulomb friction coefficient, and thus the friction contribution on the flow stress can be calculated. After a stress compensation based on the obtained friction coefficient, the calculated stress ratios led to the monitoring of the goodness of different yield surfaces.

20 August 2023
Verified
Book Chapter
Closed access
PDF file
DSDániel Gy. Szőke
Dániel Gy. Szőke
MKMartin László Kölüs
Martin László Kölüs
RBRichárd Borbély
Richárd Borbély
GBGábor J. Béres
Gábor J. Béres

1 January 2023 in Gradus
Verified
Journal Article
Closed access
MKMartin László Kölüs
Martin László Kölüs
RBRichárd Borbély
Richárd Borbély
DSDániel Szőke
Dániel Szőke
GBGábor J. Béres
Gábor J. Béres

20 October 2026 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
MKMartin László Kölüs
Martin László Kölüs
INImre Nagy-Gombai
Imre Nagy-Gombai
GBGábor J. Béres
Gábor J. Béres
GKGabor Kalacska
Gabor Kalacska
The stack compression test (SCT) represents an efficient method for characterizing the large deformation behavior of sheet metals and obtaining material parameters for finite element simulations. However, the experimental procedure is affected by several conditions that can lead to uncertainties, particularly regarding the friction conditions between individual specimen layers. Inverse modeling based on finite element simulations offers a potential solution; however, the complex deformation mechanisms within multilayer stacks frequently result in numerical instabilities. Preliminary investigations show that model parameterization strongly influences simulation accountability, while minor variations in friction coefficients may lead to numerical failure. Therefore, this study examines the effects of mesh type and meshing strategy to establish a stable and reliable computational framework for SCT simulations.