TOUGGUI Youssef

Mr. TOUGGUI Youssef


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 June 2021 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
TYTOUGGUI Youssef
TOUGGUI Youssef
AUAlper Uysal
Alper Uysal
UEUğur Emiroglu
Uğur Emiroglu
SBSalim Belhadi
Salim Belhadi
MTMustapha Temmar
Mustapha Temmar

9 July 2020 in SN Applied Sciences
Verified
Journal Article
Closed access
PDF file
TYTOUGGUI Youssef
TOUGGUI Youssef
SBSalim Belhadi
Salim Belhadi
SMSalah-Eddine Mechraoui
Salah-Eddine Mechraoui
AUAlper Uysal
Alper Uysal
MYMohammed Athmane Yallese
Mohammed Athmane Yallese
MTMustapha Temmar
Mustapha Temmar

18 November 2020 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
TYTOUGGUI Youssef
TOUGGUI Youssef
SBSalim Belhadi
Salim Belhadi
AUAlper Uysal
Alper Uysal
MTMustapha Temmar
Mustapha Temmar
MYMohamed Athmane Yallese
Mohamed Athmane Yallese

21 December 2020 in Matériaux & Techniques
Verified
Journal Article
Closed access
PDF file
TYTOUGGUI Youssef
TOUGGUI Youssef
SBSalim Belhadi
Salim Belhadi
TMTarek Mabrouki
Tarek Mabrouki
MTMustapha Temmar
Mustapha Temmar
MYMohamed Athmane Yallese
Mohamed Athmane Yallese
Austenitic stainless steel (AISI 316L ASS) is known as a very difficult material to cut due to its high toughness, work hardening combined with built-up-edge (BUE) formation and also poor thermal conductivity. In order to improve its machinability, it seems important to carry out experimentation helping to study effects of cutting parameters on process responses. For that both Taguchi and TOPSIS approaches were applied to determine an optimal combination of cutting parameters during dry turning of AISI 316L ASS. Cutting speed (Vc), feed (f), cutting depth (ap) and cutting time (tc) were selected as four input parameters. Flank wear (VB), tangential cutting force (Fz), surface roughness (Ra) and material removal rate (MRR) were considered as the major process responses. Nine cutting tests were carried out based on Taguchi's L9 orthogonal array. Thus, in order to distinguish the greater significant cutting parameter, Analysis of variance (ANOVA) was applied. Ultimately, in the case of Taguchi approach results show optimal combinations in terms of (Vc, f, ap and tc) for attaining minimum VB, Fz and Ra and also reaching maximization of MRR. In addition, TOPSIS approach was exploited yielding to results that indicate optimal combination of cutting parameters for achieving simultaneously minimum VB, Fz and Ra and maximum MRR.

15 January 2024 in Archive of Mechanical Engineering
Verified
Journal Article
Closed access
PDF file
THTallal Hakmi
Tallal Hakmi
AHAmine Hamdi
Amine Hamdi
TYTOUGGUI Youssef
TOUGGUI Youssef
Aissa LaouissiAissa Laouissi
Aissa Laouissi
SBSalim Belhadi
Salim Belhadi
MYMohamed Athmane Yallese
Mohamed Athmane Yallese
This paper presents a study on the dry turning of polyoxymethylene copolymer POM-C. The effect of five factors (cutting speed, feed rate, depth of cut, nose radius, and main cutting edge angle) on machinability is evaluated using four output parameters: surface roughness, tangential force, cutting power, and material removal rate. To do so, the study relies on three approaches: (i) Pareto statistical analysis, (ii) multiple linear regression modeling, and (iii) optimization using the genetic algorithm. To conduct the investigation, mathematical models are developed using response surface methodology based on the Taguchi L16 orthogonal array. The results indicate that feed rate, nose radius, and cutting edge angle significantly influence surface quality, while depth of cut, feed, and speed have a notable impact on other machinability parameters. The developed mathematical models have determination coefficients greater than or very close to 95%, making them very useful for the industry as they allow predicting response values based on the chosen cutting parameters. Finally, the optimization using the genetic algorithm proves to be promising and effective in determining the optimal cutting parameters to maximize productivity while improving surface quality.