Recent works in the development of nanostructured catalysts for bromate reduction in drinking water under hydrogen have highlighted the importance of the properties of the metallic phase support in their overall performance. Since most works in catalyst development are carried out in powder form, there is an overlooked gap in the correlation between catalyst support properties and performance in typical continuous applications such as fixed bed reactors. In this work, it is shown that the mechanical modification of commercially available carbon nanotubes, one of the most promising supports, can significantly enhance the activity of the catalytic system when tested in a stirred tank reactor, but upon transition to a fixed bed reactor, the formation of preferential pathways for the liquid flow and high pressure drops were observed. This effect could be minimized by the addition of an inert filler to increase the bed porosity; however, the improvement in catalytic performance when compared with the as-received support material was not retained. The operation of the continuous catalytic system was then optimized using a 1 wt.% Pd catalyst supported on the as-received carbon nanotubes. Effluent and hydrogen flow rates as well as catalyst loadings were systematically optimized to find an efficient set of parameters for the operation of the system, regarding its catalytic performance, capacity to treat large effluent flows, and minimization of catalyst and hydrogen requirements. Experiments carried out in the presence of distilled water as a reaction medium demonstrate that bromate can be efficiently removed from the liquid phase, whereas when using a real water matrix, a tendency for the deactivation of the catalyst over time was more apparent throughout 200 flow passages over the catalytic bed, which was mostly attributed to the competitive adsorption of inorganic matter on the catalyst active centers, or the formation of mineral deposits blocking access to the catalyst.
The demand for fresh water is increasing daily, requiring industries to take action to reduce the need for fresh water. Winemaking industries represent a massive hydric impact by combining the water consumed and the high volume of wastewater produced. The sun-driven photooxidation process has been widely employed in removing wastewater pollutants. This work employed four photosensitizers, Rose Bengal, AlPcS4, ZnPcS4, and TPP, for water reuse in cellars. A secondary effluent has been investigated as a water matrix. Of all the photosensitizers (PS) employed, ZnPcS4 showed better chemical oxygen demand (COD) (23%) and phenolic (TPh) (81%) removal. The effect of pH and concentration was also assessed for ZnPcS4. The phenolic content removal was found to be highly dependent on the solution’s pH, as alkaline solutions improve the singlet oxygen quantum yield where the use of a pH = 11 reached 42% and 81% of COD and TPH removal. However, a pH higher than 7 showed higher PS bleaching than pH = 7. Three different PS concentrations were evaluated: 3 × 10−6, 5 × 10−6, and 1 × 10−5 mol/L. The optimal PS concentration was found to be 5 × 10−6 mol/L.
In this study, the heterogeneous photosensitized oxidation treatment of winery effluents was optimized using chitosan carriers immobilized with Zn(II) Phthalocyanine tetrasulfonic acid. The influence of main operating parameters such as initial pH, aeration flow rate, photocatalyst load, and concentration of the photosensitizer used in the photocatalysts’ preparation was investigated. Results for chemical oxygen demand (COD) and phenolic content (TPh) removals are presented for each of the tests performed. Best reductions were obtained after 30 min of treatment in natural sunlight at an initial pH of 4.0 and an aeration flow of 2.8 L/min since it allowed reductions of 45% for COD and 73% for phenolic content (TPh). In addition, the possibility of reusing the photocatalysts during several cycles was also assessed, where an acidic initial pH allowed their reuse, being the only pH value studied where the leaching of the photosensitizer was not observed. In these conditions, the same photocatalysts were reused for six reaction cycles, and efficiency started to decrease after the third use. Thus, a greater mass and concentration of photosensitizer contributed to a superior reduction in organic matter. The results show that heterogeneous photosensitized oxidation using sunlight radiation as an energy source is an interesting approach for obtaining reusable water from winery effluents.