The tunnel field-effect transistor (TFET) is regarded as one of the most promising solid-state switches to overcome the power dissipation challenge in ultra-low power integrated circuits. TFETs take advantage of quantum mechanical tunneling hence exploit a different current control mechanism compared to standard MOSFETs. In this review, we describe state-of-the-art development of TFET both in terms of performances and of materials integration and we identify the main remaining technological challenges such as heterojunction defects and oxide/channel interface traps causing trap-assisted-tunneling (TAT). Mesa-structures, planar as well as vertical geometries are examined. Conductance slope analysis on InAs/GaSb nanowire tunnel diodes are reported, these two-terminal measurements can be relevant to investigate the tunneling behavior. A special focus is dedicated to III–V heterostructure TFET, as different groups have recently shown encouraging results achieving the predicted sub-thermionic low-voltage operation.
A high-speed plasmonic barium titanate (BTO, BaTiO 3 ) Mach-Zehnder modulator is presented. We combine nanoscale plasmonics with BTO as solid-state active material and silicon nitride (SiN) for versatile and low loss waveguiding, and integrate them in a monolithic platform. We demonstrate a plasmonic BTO modulator processed onto foundry-produced SiN. The 15 µm long high-speed modulator features a flat electro-optic frequency response up to 70 GHz and is expected to be flat way beyond. A low V π L product of 144 Vµm is shown. Data experiments reaching 216 Gbit/s with a 216 GBd 2PAM signal and 256 Gbit/s with a 128 GBd 4PAM signal are demonstrated. The merger of the versatile silicon nitride platform with high-speed plasmonics using the highly nonlinear ferroelectric BTO is an attractive solution as a future Tb/s optical interconnect platform.
InGaAs is a potential candidate for Si replacement in upcoming advanced technological nodes because of its excellent electron transport properties and relatively low interface defect density in dielectric gate stacks. Therefore, integrating InGaAs devices with the established Si platforms is highly important. Using template-assisted selective epitaxy (TASE), InGaAs nanowires can be monolithically integrated with high crystal quality, although the mechanisms of group III incorporation in this ternary material have not been thoroughly investigated. Here we present a detailed study of the compositional variations of InGaAs nanostructures epitaxially grown on Si(111) and Silicon-on-insulator substrates by TASE. We present a combination of XRD data and detailed EELS maps and find that the final Ga/In chemical composition depends strongly on both growth parameters and the growth facet type, leading to complex compositional sub-structures throughout the crystals. We can further conclude that the composition is governed by the facet-dependent chemical reaction rates at low temperature and low V/III ratio, while at higher temperature and V/III ratio, the incorporation is transport limited. In this case we see indications that the transport is a competition between Knudsen flow and surface diffusion.
III-V semiconductors are being considered as promising candidates to replace silicon channel for low-power logic and RF applications in advanced technology nodes. InGaAs is particularly suitable as the channel material in n-type metal-oxide-semiconductor field-effect transistors (MOSFETs), due to its high electron mobility. In the present work, we report on InGaAs FinFETs monolithically integrated on silicon substrates. The InGaAs channels are created by metal–organic chemical vapor deposition (MOCVD) epitaxial growth within oxide cavities, a technique referred to as template-assisted selective epitaxy (TASE), which allows for the local integration of different III-V semiconductors on silicon. FinFETs with a gate length down to 20nm are fabricated based on a CMOS-compatible replacement-metal-gate process flow. This includes self-aligned source-drain n+ InGaAs regrown contacts as well as 4 nm source-drain spacers for gate-contacts isolation. The InGaAs material was examined by scanning transmission electron microscopy (STEM) and the epitaxial structures showed good crystal quality. Furthermore, we demonstrate a controlled InGaAs digital etching process to create doped extensions underneath the source-drain spacer regions. We report a device with gate length of 90 nm and fin width of 40 nm showing on-current of 100 µA/µm and subthreshold slope of about 85 mV/dec.
12 July 2019 in IEEE Journal of the Electron Devices Society
In this paper, we demonstrate InGaAs FinFETs 3D sequentially (3DS) integrated on top of a fully-depleted silicon-on-insulator CMOS. Top layer III-V FETs are fabricated using a Si CMOS compatible HKMG replacement gate flow and self-aligned raised source-drain regrowth. We demonstrate that the low thermal budget of the top layer process does not affect the lower level FETs performance. An on-current of 200 μA/μm (at IOFF = 100 nA/μm and VDD = 0.5 V) is achieved, representing the highest reported for 3DS integrated III-V FETs on silicon, showing a 50% improvement in RON compared to previous work. The achieved improved performance can be attributed to the introduction of spacers, doped extensions underneath the gate region as well as improvements in the direct wafer bonding technique.