Seonmin Hwang

Dr. Seonmin Hwang

Korea Institute of Materials Science, Changwon, Gyeongnam, Republic of Korea
+1
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 February 2019 in Metals
Verified
Journal Article
Open access
PDF file
Seonmin HwangSeonmin Hwang
Seonmin Hwang
DLDong-Won Lee
Dong-Won Lee
Jei-Pil WangJei-Pil Wang
Jei-Pil Wang
The metallic tantalum powder was successfully synthesized via reduction of tantalum pentoxide (Ta2O5) with magnesium gas at 1073~1223 K for 10 h inside the chamber held under an argon atmosphere. The powder obtained after reduction shows the Ta–MgO mixed structure and that the MgO component was dissolved and removed fully via stirring in a water-based HCl solution. The particle size in the tantalum powder obtained after acid leaching was shown to be in a range of 50~300 nm, and the mean internal crystallite sizes measured by the Scherrer equation varied from 11.5 to 24.7 nm according to the increase in reduction temperatures. The temperature satisfactory for a maximal reduction effect was found to be 1173 K because the oxygen content was minimally saturated to about 1.3 wt %.

1 November 2021 in International Journal of Refractory Metals and Hard Materials
Verified
Journal Article
Closed access
Seonmin HwangSeonmin Hwang
Seonmin Hwang
SPSu-Jin Park
Su-Jin Park
JWJei-Pil Wang
Jei-Pil Wang
YPYong-Ho Park
Yong-Ho Park
DLDong-Won Lee
Dong-Won Lee

1 January 2021 in MATERIALS TRANSACTIONS
Verified
Journal Article
Closed access
PDF file
SPSu-Jin Park
Su-Jin Park
Seonmin HwangSeonmin Hwang
Seonmin Hwang
JWJei-Pil Wang
Jei-Pil Wang
YSYoung-Guk Son
Young-Guk Son
DLDong-Won Lee
Dong-Won Lee
It was tried to find the optimal condition to prepare the metallic niobium powder with minimal oxygen content by atmospheric magnesium-gas reduction of niobium pentoxide (Nb2O5) powder at 1073–1223 K, which are industrially moderate and low temperature ranges until maximally 80 h inside the chamber held under the argon circumstances of 110 kPa. Magnesium oxide of the by-product of the reduction, was dissolved and removed fully by dissolving in a 10% aqueous hydrochloric acid solution. The particle size of the niobium powder reduced for 20 h was slightly increased within the range of 200∼600 nm according to increase of reduction temperatures. And such fine particles were further coarsened to near 1 µm by increase of reduction times until 80 h at 1173 K, which is thought to be the most suitable for magnesium-gas reduction to be applied in industry. The reduction time satisfied for a maximal reduction effect was found to be 60 hours as the oxygen content was then minimally saturated to about 0.42 wt.%. Furthermore, the hydrogen contamination due to acid leaching of 0.28 wt.% was fully removed by dehydrogenation, which was a heat treatment performed under vacuum at 827 K for 2 h; this resulted in the formation of metallic niobium powder.

1 September 2021 in MATERIALS TRANSACTIONS
Verified
Journal Article
Closed access
PDF file
Seonmin HwangSeonmin Hwang
Seonmin Hwang
SPSu-Jin Park
Su-Jin Park
GKGwang-Tae Kim
Gwang-Tae Kim
HKHa-Neul Kim
Ha-Neul Kim
JKJae-Woong Ko
Jae-Woong Ko
DLDong-Won Lee
Dong-Won Lee
Metallic silicon powder has been widely used for the production of various industrial materials and parts such as refractory ceramics, solar cells, military parts and so on. Herein, we attempted to prepare pure silicon powder from SiO2 by a magnesium thermal reduction process. A mixed-phase, Mg2Si + MgO, was obtained by the reduction of SiO2 powder by magnesium gas at 1223 K for 20 h. To extract pure silicon powder, Mg was separated by evaporation under vacuum through Mg2Si decomposition above 1073 K, leading to the formation of Si + MgO, and the MgO by-product was eliminated by dissolution in an aqueous hydrochloric acid solution. X-ray diffraction analysis confirmed the formation of pure Si powder and particle size shown in microstructure and oxygen content were analyzed to be 1∼5 µm and 1.5∼6 wt.%, respectively.

26 October 2022 in Materials
Verified
Journal Article
Open access
PDF file
Seonmin HwangSeonmin Hwang
Seonmin Hwang
JHJiwon Hong
Jiwon Hong
PHPark Yong ho
Park Yong ho
DLDong-Won Lee
Dong-Won Lee
Hexane is a safe, efficient, and cost-effective alternative to other commercial hydrocarbons for gaseous carburization; however, commercial hexane is not sufficiently pure. Titanium powder can remove oxygen-containing impurities from commercial hexane; however, research on the use of titanium powder remains limited. We investigated the purification of hexane using titanium, copper, and aluminum powders and used the purified hexane for the gaseous carburization of tantalum. Ti exhibited lower activation energy for oxidation (1.55 kJ/mol) than Cu (91.09 kJ/mol) and Al (150.25 kJ/mol) and a significantly higher oxidation rate (0.0269 g/h) in hexane at room temperature than Cu (0.0018 g/h) and Al (0.0001 g/h). The carbon content in tantalum carburized using the purified hexane was comparable to that carburized using unpurified hexane (approximately 6.22%); however, its oxygen content was significantly lower (1.39%), which indicates that the produced tantalum carbide has a higher purity. X-ray diffraction results revealed that the oxidation products of tantalum, such as Ta2O, TaO2, Ta0.8O2, and Ta2O5, were absent in the sample carburized using the purified hexane. Therefore, Ti powder can effectively remove oxygen-containing impurities from commercial hexane and facilitate its use as an effective carburizing medium for the synthesis of high-purity tantalum carbide.

13 October 2023 in Metals
Verified
Journal Article
Open access
PDF file
JHJiwon Hong
Jiwon Hong
Seonmin HwangSeonmin Hwang
Seonmin Hwang
Namhyun KangNamhyun Kang
Namhyun Kang
DLDong-Won Lee
Dong-Won Lee
Nb-Ti binary alloys are widely employed as high value-added materials in the manufacture of super heat-resistant alloys, biomaterials, and superconductors. Therefore, there is significant interest to produce Nb-Ti master alloys in a cost-effective manner. In this study, we investigated the magnesiothermic reduction of Nb2O5 and Ti2Nb10O29 over the temperature range of 1073 to 1223 K and comparatively evaluated the reaction outcomes. The reduction product was composed of metal (Nb or Nb-Ti) particles and MgO, which covered the surface of the reduced metal particles. After the reduction reaction, the surface MgO phase was removed by pickling with hydrochloric acid (HCl) to finally recover the Nb metal or Nb-Ti alloy as a pure product. Scanning electron microscopy and X-ray diffraction analyses of the pure Nb metal and Nb-Ti alloy powders revealed that the reduction of both raw materials was successful at temperatures exceeding 1173 K. Reaction kinetics analysis revealed that the activation energy for the reduction of the mixed metal oxide (Ti2Nb10O29) is lower than that of Nb2O5 reduction. This is because of the different reaction mechanism behaviors during reduction and the different thermodynamic stabilities of the precursors.