We demonstrate an ultracompact integrated silicon-based plasmonic sensor for lab-on-chip applications in the mid-infrared (MIR) spectral range. Our sensor possesses desirable features such as design simplicity and very high sensitivity. The sensor is designed using a platform for plasmonic effects in the MIR using highly doped silicon. This platform is exploited to create a metal-less plasmonic slot waveguide in the MIR range. This plasmonic waveguide is highly sensitive to any environmental change. Full wave electromagnetic simulations were carried out to design and optimize the structure. The proposed sensor covers a large wavelength span in the MIR range. High spectral sensitivity of was achieved for our sensor device. Further development of the structure was conducted to extend the sensor operation to multigas sensing.
10 January 2017 in Journal of Physics D: Applied Physics
We propose a plasmonic refractometric sensor that is based on Fano resonances excited in a resonant rectangular cavity coupled to a metal–insulator–metal bus waveguide. The properties of the resonances are controlled by varying the dimensions of the rectangular resonator and the observed Fano profile stems from the multimode interference of resonant cavity modes. We theoretically investigate the device’s performance as a highly sensitive refractometric plasmonic sensor which operates on gases, water and organic solvent solutions with tens of femtoliters of analyte. The sensor is studied in a wide operational range (0.7–2.7 μ m) covering the entire near infrared spectral range, and is characterized by large sensitivity, which reaches 1550 nm RIU −1 , and sensitivity per unit volume higher than 10 7 nm (RIU · nl) −1 at the resonant wavelength of 1.55 μ m. The proposed plasmonic structure is very promising for integrated sensing applications owing to its small footprint and surprisingly simple layout.
Waveguides with sub-100 nm thickness offer a promising platform for sensors. We designed and analyzed multimode interference (MMI) devices using these ultrathin platforms for use as biosensors. To verify our design methodology, we compared the measured and simulated spectra of fabricated 220-nm-thick MMI devices. Designs of the MMI biosensors based on the sub-100 nm platforms have been optimized using finite difference time domain simulations. At a length of 4 mm, the 50-nm-thick MMI sensor provides a sensitivity of roughly 420 nm/RIU and with a figure of merit (FOM) definition of sensitivity/full-width-at-half-maximum, the FOM is 133. On the other hand, using a thickness of 70 nm results in a more compact design—only 2.4 mm length was required to achieve a similar FOM, 134, with a sensitivity of 330 nm/RIU. The limits of detection (LOD) were calculated to be 7.1 × 10−6 RIU and 8.6 × 10−6 RIU for the 50 nm and the 70-nm-thick sensor, respectively. The LOD for glucose sensing was calculated to be less than 10 mg dL−1 making it useful for detecting glucose in the diabetic range. The biosensor is also predicted to be able to detect layers of protein, such as biotin-streptavidin as thin as 1 nm. The ultrathin SOI waveguide platform is promising in biosensing applications using this simple MMI structure.
We propose a highly sensitive optical sensor which is built from silicon nanowires. The silicon nanowires are arranged to form a ring resonator. The silicon nanowires cladding and voids are filled with the analyte. The sensor has a small footprint of 16 μm × 16.5 μm. The insertion loss of the sensor is only 0.4 dB, while it is characterized by its high sensitivity of 430 nm/RIU. As a biosensor, our device showed a 100 nm/RIU sensitivity when a thin biolayer of 10 nm thickness is attached to the silicon nanowire structures.
The existence of surface plasmon polaritons in doped silicon micro-scale structures has opened up new and innovative possibilities for applications, such as sensing, imaging, and photonics. A CMOS-compatible doped Si plasmonic sensor is proposed and investigated. The plasmon resonance can be tuned by controlling the carrier density and dopant concentration. In this paper, we demonstrate that using silicon doped with phosphorus at a concentration of 5 × 10 cm can induce surface plasmon resonance in the mid-infrared region. Two ring resonators of two different radii based on metal–insulator–metal waveguide structures are studied individually. Then, the two ring resonators are integrated in the same device. When the two ring resonators are coupled and resonate at the same frequency; two distinct resonance spectral lines are generated with striking features that improve its potential use for sensing and modulation applications. The propagating plasmonic mode is studied, including its mode profile and bend loss. We evaluate the effectiveness of a microstructure gas sensor with dimensions of 15 m × 15 m by measuring its sensitivity and selectivity towards methane and ethane gases. Small alterations in the surrounding refractive index led to noticeable shifts in the resonance peak. The sensor achieved a sensitivity of 7539.9 nm/RIU at the mid-infrared spectral range around the 7.7 m wavelength. Furthermore, by combining the resonators, we can achieve a smaller full width at half maximum (FWHM), which will ultimately result in greater sensitivity than using a single-ring resonator or other plasmonic resonator configurations. Once the sensitivity and selectivity of the sensor are measured, the FOM can be calculated by dividing the sensitivity by the selectivity of the sensor, resulting in an FOM of 6732.
All CMOS modulator based on directional coupler configuration is presented, simulated, and analyzed. The device structure utilizes the silicon-organic hybrid platform. The waveguides are made of arrays of silicon nanowires on a bulk silicon dioxide substrate. While the cladding and the voids between the silicon nanowires are filled with an electro-optic polymer. When the voltage applied across the electro-optic polymer layer changes, the polymer will have its refractive index value changed, leading to a change in the effective index. Thus, under directional coupler operation, we control the power coupled and exchanged between the two arms of the directional coupler. Utilizing Finite Difference Time Domain simulations tools, we design and simulate the operation of the modulator at the telecommunication wavelength, with promising extinction ratios.