Amina Aljaber

Dr. Amina Aljaber

orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 March 2019 in Materials
Verified
Journal Article
Open access
PDF file
AZAbdallah F Zedan
Abdallah F Zedan
AAAmina Aljaber
Amina Aljaber
In this study, xCuO-CeO2 mixed oxide catalysts (Cu weight ratio x = 1.5, 3, 4.5, 6 and 15 wt.%) were prepared using solution combustion synthesis (SCS) and their catalytic activities towards the methane (CH4) oxidation reaction were studied. The combustion synthesis of the pure CeO2 and the CuO-CeO2 solid solution catalysts was performed using copper and/or cerium nitrate salt as an oxidizer and citric acid as a fuel. A variety of standard techniques, including scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), thermo-gravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy were employed to reveal the microstructural, crystal, thermal and electronic properties that may affect the performance of CH4 oxidation. The CuO subphase was detected in the prepared solid solution and confirmed with XRD and Raman spectroscopy, as indicated by the XRD peaks at diffraction angles of 35.3° and 38.5° and the Ag Raman mode at 289 cm−1, which are characteristics of tenorite CuO. A profound influence of Cu content was evident, not only affecting the structural and electronic properties of the catalysts, but also the performance of catalysts in the CH4 oxidation. The presence of Cu in the CeO2 lattice obviously promoted its catalytic activity for CH4 catalytic oxidation. Among the prepared catalysts, the 6% CuO-CeO2 catalyst demonstrated the highest performance, with T50 = 502 °C and T80 = 556 °C, an activity that is associated with the availability of a fine porous structure and the enhanced surface area of this catalyst. The results demonstrate that nanocrystalline copper-ceria mixed oxide catalysts could serve as an inexpensive and active material for CH4 combustion.

1 September 2020 in Sensors
Verified
Journal Article
Open access
PDF file
MEMohamed Y. Elsayed
Mohamed Y. Elsayed
SMSherif Mohamed
Sherif Mohamed
AAAmina Aljaber
Amina Aljaber
MSMohamed Swillam
Mohamed Swillam
Waveguides with sub-100 nm thickness offer a promising platform for sensors. We designed and analyzed multimode interference (MMI) devices using these ultrathin platforms for use as biosensors. To verify our design methodology, we compared the measured and simulated spectra of fabricated 220-nm-thick MMI devices. Designs of the MMI biosensors based on the sub-100 nm platforms have been optimized using finite difference time domain simulations. At a length of 4 mm, the 50-nm-thick MMI sensor provides a sensitivity of roughly 420 nm/RIU and with a figure of merit (FOM) definition of sensitivity/full-width-at-half-maximum, the FOM is 133. On the other hand, using a thickness of 70 nm results in a more compact design—only 2.4 mm length was required to achieve a similar FOM, 134, with a sensitivity of 330 nm/RIU. The limits of detection (LOD) were calculated to be 7.1 × 10−6 RIU and 8.6 × 10−6 RIU for the 50 nm and the 70-nm-thick sensor, respectively. The LOD for glucose sensing was calculated to be less than 10 mg dL−1 making it useful for detecting glucose in the diabetic range. The biosensor is also predicted to be able to detect layers of protein, such as biotin-streptavidin as thin as 1 nm. The ultrathin SOI waveguide platform is promising in biosensing applications using this simple MMI structure.

1 October 2008 in Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy
Verified
Journal Article
Closed access
AAAmina Aljaber
Amina Aljaber
ENEl-Metwally Nour
El-Metwally Nour

15 June 2022 in Nanomaterials
Verified
Journal Article
Open access
PDF file
YSYahia Shoeb
Yahia Shoeb
AHAymen S. Abu Hatab
Aymen S. Abu Hatab
AMAssem Mohamed
Assem Mohamed
MAMohammed S. Al-Kuwari
Mohammed S. Al-Kuwari
AAAmina Aljaber
Amina Aljaber
Siham Y Al-QaradawiSiham Y Al-Qaradawi
Siham Y Al-Qaradawi
Assigned to their outstanding physicochemical properties, TiO2-based materials have been studied in various applications. Herein, TiO2 doped with different Mo contents (Mo-TiO2) was synthesized via a microwave-assisted solvothermal approach. This was achieved using titanium (IV) butoxide and molybdenum (III) chloride as a precursor and dodecylamine as a surface directing agent. The uniform effective heating delivered by microwave heating reduced the reaction time to less than 30 min, representing several orders of magnitude lower than conventional heating methods. The average particle size ranged between 9.7 and 27.5 nm and it decreased with increasing the Mo content. Furthermore, Mo-TiO2 revealed mesoporous architectures with a high surface area ranging between 170 and 260 m2 g−1, which is superior compared to previously reported Mo-doped TiO2. The performance of Mo-TiO2 was evaluated towards the adsorption of Rhodamine B (RhB). In contrast to TiO2, which revealed negligible adsorption for RhB, Mo-doped samples depicted rapid adsorption for RhB, with a rate that increased with the increase in Mo content. Additionally, Mo-TiO2 expressed enhanced adsorption kinetics for RhB compared to state-of-the-art adsorbents. The introduced synthesis procedure holds a grand promise for the versatile synthesis of metal-doped TiO2 nanostructures with outstanding physicochemical properties.

18 April 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
AKAdnan Khan
Adnan Khan
PMPenchal Matli
Penchal Matli
Muddasir NawazMuddasir Nawaz
Muddasir Nawaz
MMManohar Reddy Mattli
Manohar Reddy Mattli
Gururaj ParandeGururaj Parande
Gururaj Parande
Manoj GuptaManoj Gupta
Manoj Gupta
In this study, Al-BiSn composites were synthesized by a combination of microwave sintering and hot extrusion processes. The structural, morphological, mechanical, and thermal properties were investigated to elucidate the role of Bi60Sn40 (BiSn) alloy content (5, 10, and 15 wt.%) in modifying the properties of Al-BiSn composites. The X-ray diffraction (XRD) patterns confirmed the presence of aluminum and BiSn particles. Distribution of BiSn particles in Al-BiSn composites was confirmed by field emission scanning electron microscopy associated with energy dispersive X-ray analysis (FE-SEM-EDX). Results indicated that hot extruded Al-(15 wt.% BiSn) composite exhibits maximum hardness (78 ± 4 Hv) and tensile strength (185 ± 3 MPa), which were 117% and 58% improvements, respectively, compared to pure Al. This improvement in mechanical properties can be attributed to the strengthening effect of BiSn particles. A decline in the values of the coefficient of thermal expansion (CTE) with an increasing amount of BiSn particles reflects the enhanced thermal stability of developed Al-BiSn composites. The promising properties of Al-BiSn composites make them suitable for many industrial applications.

25 June 2021 in Nanomaterials
Verified
Journal Article
Open access
PDF file
AZAbdallah F Zedan
Abdallah F Zedan
SGsafa Gaber
safa Gaber
AAAmina Aljaber
Amina Aljaber
Kyriaki PolychronopoulouKyriaki Polychronopoulou
Kyriaki Polychronopoulou
Significant improvement of the catalytic activity of palladium-based catalysts toward carbon monoxide (CO) oxidation reaction has been achieved through alloying and using different support materials. This work demonstrates the promoting effects of the nanointerface and the morphological features of the support on the CO oxidation reaction using a Pd-Cu/TiO2 catalyst. Pd-Cu catalysts supported on TiO2 were synthesized with wet chemical approaches and their catalytic activities for CO oxidation reaction were evaluated. The physicochemical properties of the prepared catalysts were studied using standard characterization tools including SEM, EDX, XRD, XPS, and Raman. The effects of the nanointerface between Pd and Cu and the morphology of the TiO2 support were investigated using three different-shaped TiO2 nanoparticles, namely spheres, nanotubes, and nanowires. The Pd catalysts that are modified through nanointerfacing with Cu and supported on TiO2 nanowires demonstrated the highest CO oxidation rates, reaching 100% CO conversion at temperature regime down to near-ambient temperatures of ~45 °C, compared to 70 °C and 150 °C in the case of pure Pd and pure Cu counterpart catalysts on the same support, respectively. The optimized Pd-Cu/TiO2 nanowires nanostructured system could serve as efficient and durable catalyst for CO oxidation at near-ambient temperature.