Andrey Manokhin

Dr. Andrey Manokhin

orcid

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2018 in Journal of Superhard Materials
Verified
Journal Article
Closed access
PDF file
AMAndrey Manokhin
Andrey Manokhin
SKS. An. Klimenko
S. An. Klimenko
VBV. M. Beresnev
V. M. Beresnev
The paper reviews the present-day trends in the development of new types of wear-resistant coatings, including nanostructured ones, for PCBN tools. The main currently pursued approaches to creation...

1 February 2009 in Journal of Superhard Materials
Verified
Journal Article
Closed access
PDF file
SKS. A. Klimenko
S. A. Klimenko
AMAndrey Manokhin
Andrey Manokhin
The results of the comprehensive studies of a highly efficient method of finishing, the so-called hard “skiving” turning, are discussed. Special features of the oblique cutting with a tool equipped with cBN-based polycrystalline superhard materials are shown, the regularities of the surface roughness formation and surface layer hardening in machining are considered.

2 June 2022 in East European Journal of Physics
Verified
Journal Article
Open access
PDF file
VBVyacheslav M. Beresnev
Vyacheslav M. Beresnev
OMOlga Maksakova
Olga Maksakova
SLSerhiy V. Lytovchenko
Serhiy V. Lytovchenko
SKSerhiy A. Klymenko
Serhiy A. Klymenko
DHDenis V. Horokh
Denis V. Horokh
VSViacheslav Stolbovyi
Viacheslav Stolbovyi
Multilayer (TiSi)N/CrN coatings were fabricated through vacuum-arc deposition by applying the arc currents of (100 ÷ 110) A on TiSi cathode and (80 ÷ 90) A on Cr cathode, negative bias potential connected to the substrate holder of –(100 ÷ 200) V and reactive gas pressure of (0.03 ÷ 0.6) Pa. Applying a negative bias voltage on substrates enhanced the ion bombardment effect, which affected the chemical compositions, phase state, mechanical and tribological properties of (TiSi)N/CrN coatings. Obtained results indicated that (TiSi)N/CrN coatings with Si content ranging from 0.53 to 1.02 at. % exhibited a high hardness level of (22.1 ÷ 31.1) GPa accompanied with a high Young’s modulus of (209 ÷ 305) GPa, H/E* level of (0.080 ÷ 0.100), H3/E*2 level of (0.15 ÷ 0.33) GPa, and the friction coefficient of 0.35. Values of critical loads at dynamic indentation, changes in friction coefficient and level of acoustic emission signal evidence the high adhesive strength of (TiSi)N/CrN coatings, which allows recommending them to increase cutting tool performance.

1 November 2025 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
NBNataliia Balytska
Nataliia Balytska
LPLars Penter
Lars Penter
AMAndrey Manokhin
Andrey Manokhin
SISteffen Ihlenfeldt
Steffen Ihlenfeldt
NiTi shape memory alloys hold significant potential for advanced applications in biomedical and high-performance engineering fields, making the development of reliable and efficient manufacturing technologies increasingly critical. The face milling process of NiTi alloys requires thorough investigation, both as a pre-processing operation—particularly in the context of assessing technological heritage—and as a standalone technique. This study investigated the face milling performance of austenitic Ni 56.5 Ti 43.5 (wt.%) shape memory alloy as a function of cutting conditions in dry machining with uncoated cemented carbide cutting inserts. Tests were performed at different cutting speeds (20, 35, and 50 m/min), feed rates (0.05, 0.1, and 0.15 mm/tooth), and axial depths of cut (0.5, 0.75, and 1.0 mm). The article describes the cutting force components, temperature, surface roughness of the milled surface, tool wear, microstructure, and depth of the machining-induced layers, as well as the chip morphology. Cross-section analysis revealed a heterogeneous surface layer with a predominant martensite content and a deeper subsurface layer with irregular, deep martensite needles. The influence of cutting conditions on the depth of each of these layers is discussed. The failure modes of the cutting insert and the wear mechanism are determined. The findings deepen the understanding of the thermo-mechanical responses of NiTi during face milling, especially the extensive phase transformations that occur in the surface layer. The study emphasizes the importance of identifying and removing the mechanically affected layer in post-machining steps to preserve the alloy’s functional properties.

1 June 2023 in Journal of Superhard Materials
Verified
Journal Article
Closed access
PDF file
XLXin Li
Xin Li
FTFei Teng
Fei Teng
AMAndrey Manokhin
Andrey Manokhin
Junjie ZhangJunjie Zhang
Junjie Zhang
TSTao Sun
Tao Sun
OPO. O. Pasichny
O. O. Pasichny
Some results of experimental studies on the specific features inherent in the intermittent cutting of quenched steel AISI 52100 with a PcBN tool were prese

1 October 2022 in Journal of Superhard Materials
Verified
Journal Article
Closed access
PDF file
AMAndrey Manokhin
Andrey Manokhin
VSV. O. Stolboviy
V. O. Stolboviy
IKI. V. Kolodiy
I. V. Kolodiy
MKM. Yu. Kopieikina
M. Yu. Kopieikina
SKS. An. Klymenko
S. An. Klymenko
ISI. V. Serdyuk
I. V. Serdyuk
Residual stresses in vacuum-arc coatings of the TiAlSiYN system deposited on a PcBN base were studied by X-ray diffractometry. The substructure characteris